3-818-19-0770 3818190770 ROD L 270mm D 8mm Woodworking Machine Spare Parts for Homag

When a rod on a Homag machine bends or wears, the linked mechanism loses alignment and the machine may not hold position through the cycle. Replacing the rod restores the original geometry. This rod is sized to the original 270 mm length and 8 mm diameter, so the linkage returns to its designed setting without shimming or adjustment.

The rod is a steel shaft, 270 mm long and 8 mm in diameter, with part number 3-818-19-0770 3818190770. It fits Homag woodworking machines as a spare part. To confirm the fit, compare the number on your machine's parts list with 3-818-19-0770 3818190770, then measure the old rod: 270 mm end to end and 8 mm across the shaft.

Before installation, check the rod's mounting points for wear and confirm the bore that receives the 8 mm shaft is clean. A rod that slides into place without force indicates the bore and rod diameter match. During use, the steel shaft carries the load between the connected parts, so any bend or flat spot on the old rod shows where to inspect the mating components.

Supply is straightforward: the rod is packed as a single spare part. Customisation is not stated. When you enquire, send the part number 3-818-19-0770 3818190770, the quantity you need, and a photo or measurement of the old rod.

What the specification fixes, and what it leaves to the machine:

• Replacement fit for Homag machines — The rod is intended for Homag woodworking machines, so it replaces the original rod without adapting the machine frame or linkage.
• Length check before install — At 270 mm long, the rod matches the original length; compare it to your old rod to confirm the linkage geometry stays as designed.
• Diameter for bore match — The 8 mm diameter suits the original bore; check the mating bore for wear before pressing the rod into place.
• Steel shaft material — Steel construction gives the rod stiffness along its 270 mm length, so it resists bending under the load between connected parts.
• Wear point at the ends — Inspect both ends of the old rod for flats or scoring; these show whether the mating pins or bores also need attention.
• Installation without force — A correct 8 mm fit lets the rod slide into its bore by hand; if it needs force, stop and check the bore for burrs or damage.
• Alignment check after fitting — After fitting the 270 mm rod, cycle the machine slowly and watch the linkage to confirm the rod moves without binding.

What changes on the shop floor when the right part goes back in:

• Restores original linkage geometry. Fitting a rod of 270 mm length and 8 mm diameter returns the mechanism to its designed setting, so the machine holds position through the cycle without extra adjustment.
• Reduces guesswork at the parts counter. The part number 3-818-19-0770 3818190770 ties directly to the Homag parts list, so you can order the correct rod without measuring and hoping.
• Steel resists bending in service. A steel shaft of 8 mm diameter carries the load between connected parts and keeps its shape, so the linkage stays aligned during repeated machine cycles.
• Simple wear inspection. Checking the ends of the old rod for flats or scoring takes minutes and tells you whether the mating pins or bores also need replacement before refitting.
• Straightforward installation. Because the rod is a single 270 mm steel shaft, it slides into place by hand when the bore is clean, cutting the time the machine stays down.
• Clear enquiry process. Sending the part number and a photo of the old rod lets the supplier check the 270 mm length and 8 mm diameter against your machine before shipping.

Match the part number 3-818-19-0770 3818190770 to your machine's parts list and measure your old rod at 270 mm long and 8 mm in diameter. If both match, the rod is the correct replacement.

Steel. The rod is a steel shaft with an 8 mm diameter and a 270 mm length, intended for Homag woodworking machines as a spare part.

Yes, if you can access the rod's mounting points. Slide the 8 mm shaft into the bore by hand, and if it needs force, check the bore for burrs or wear before proceeding.

Check the part number on your machine and measure the old rod: 270 mm end to end and 8 mm across the shaft. Also inspect the mating bores for wear that could affect the fit.

No custom sizes are stated for this rod. It is supplied as a 270 mm long, 8 mm diameter steel rod under part number 3-818-19-0770 3818190770.

The rod is packed as a single spare part. Keep it straight in storage to avoid bending the 8 mm shaft before installation.

Send the part number 3-818-19-0770 3818190770, the quantity you need, and a photo or measurement of the old rod showing 270 mm length and 8 mm diameter.

This rod is intended for Homag woodworking machines. For other brands, check your own parts list and dimensions against 270 mm length and 8 mm diameter before ordering.