4-075-01-1147 Rexroth R911316056 AC-MOTOR 8 NM INDRA DYN S MSK061C-UG0

When a Homag machine stops mid-cycle, a failed AC motor on the axis or feed is often the cause. The motor no longer holds torque, motion control drops out, and production stalls. This Rexroth R911316056 restores the drive at 8 Nm so the machine can run again.

This is a 3-phase synchronous PM-motor from Rexroth, model MSK061C-UG0 in the Indra Dyn S range. It weighs 8.3 KGS and carries part number 4-075-01-1147 or 4075011147. It fits Homag woodworking machines. Confirm the fit by matching both the part number and the model number on the motor you remove.

Before fitting, compare the model number on the old motor to R911316056 and check the 8 Nm torque rating matches the axis you are repairing. Mounting and connection follow the machine's existing motor position. A correct match means the drive picks up the motor without changes to the machine setup.

Supply is handled as a spare part for Homag machines. Packing and customisation are not stated here. Send the part number 4-075-01-1147, the model R911316056, and a photo of the motor nameplate with your enquiry so the correct unit is picked and shipped. Supply comes from the same range as the rest of the catalogue.

What the specification fixes, and what it leaves to the machine:

• Axis drive replacement — The 8 Nm torque rating matches the original motor so the axis returns to its designed motion control after replacement.
• Model match check — Model R911316056 and Indra Dyn S MSK061C-UG0 identify the exact motor, letting you compare against the nameplate before ordering.
• Part number cross-check — Part number 4-075-01-1147 and 4075011147 give two reference points to confirm the spare against your machine records.
• Machine fit — Built for Homag woodworking machines, the motor drops into the existing motor position without adapter plates on the machine.
• Weight handling — At 8.3 KGS the motor is manageable for one person during removal and refitting on the machine frame.
• Motor construction —
• Wear point — The motor is the wear point when torque drops or motion control faults appear; replacing it addresses the source, not the symptom.
• Installation check — Compare the model and 8 Nm rating on the old motor before mounting, so the replacement matches the axis being repaired.
• Spare stock planning — Holding one 8 Nm motor on the shelf cuts the wait when a Homag machine stops on a motor fault.
• Enquiry accuracy — Quoting 4-075-01-1147, R911316056 and a nameplate photo with your enquiry removes ambiguity about which motor you need.

What changes on the shop floor once the unit is in place:

• Gets the machine back on the line. A failed motor stops the whole machine. Fitting the correct 8 Nm Rexroth unit restores axis motion and lets production resume without waiting on a wrong part.
• Fit confirmed before you pay. Two part numbers and one model number give you three checks against the old motor, so you avoid return shipping on a unit that will not mount.
• One person can handle the swap. At 8.3 KGS the motor is light enough for a single technician to remove and refit, keeping downtime short and labour cost down.
• Torque matches the original. The 8 Nm rating means the drive sees the motor it was set up for, so motion control behaves as it did before the failure.
• Spare kept ready on the shelf. Keeping one R911316056 in store means a motor fault becomes a same-day fix instead of a wait for delivery from outside.
• Clear part identification. Model MSK061C-UG0 and part 4075011147 are stamped references your maintenance team can read straight off the old motor and match.
• Built for Homag machines. The motor is intended for Homag woodworking equipment, so it fits the motor position and connection layout already on your machine.

It fits Homag woodworking machines. Check the motor position and the old motor's part number against 4-075-01-1147 or 4075011147 before ordering.

Match both the part number and the model number. The model is R911316056, Indra Dyn S MSK061C-UG0, and the part numbers are 4-075-01-1147 and 4075011147.

The motor delivers 8 Nm. Compare this to the rating on the motor you are removing so the replacement matches the axis.

The net weight is 8.3 KGS. That is light enough for one technician to handle during removal and refitting.

It is a 3-phase synchronous PM-motor from Rexroth, an AC motor in the Indra Dyn S range.

Order quantity is not stated here. Send your required quantity with the part number and model number and the supplier will respond.

Send the part number 4-075-01-1147, the model R911316056, and a photo of the motor nameplate. That lets the supplier pick the correct unit.

Packing and customisation are not stated for this motor. Ask the supplier directly when you send your enquiry with the part details.