4008320091 LIMIT SWITCH GC-UV 1 AV 1 270 GRAD Spare Parts For Homag Machine

When a Homag machine stops indexing or fails to signal end of travel, the limit switch is often the first suspect. A worn switch can leave the control without a position signal, halting the cycle. Replacing the GC-UV 1 AV 1 270 GRAD restores the signal path at the point where movement is checked.

This is a limit switch with part number 4008320091, also written 4-008-32-0091. The model is GC-UV 1 AV 1 270 GRAD and the angle of operation is 270 degrees. It fits Homag machines that use this switch. Confirm the fit by matching both the part number and the model against the switch on your machine.

Check the mounting point and the actuator alignment before fitting. The switch operates through 270 degrees, so the lever or cam must travel within that arc to trigger the contacts. Correct alignment means the signal trips at the same point every cycle, which keeps the machine sequence repeatable.

Supply runs through DHL, FedEx, UPS, and similar carriers. No customisation is stated for this switch. Send the machine model, the part number 4008320091, and a photo of the old switch with your enquiry so the correct item can be confirmed before dispatch.

What the specification fixes, and what it leaves to the machine:

• Travel detection point — The switch operates through 270 degrees, covering the arc where the machine checks position before the next step.
• Part number match — Order by 4008320091 or 4-008-32-0091 to match the switch already fitted to the machine.
• Model identification — The GC-UV 1 AV 1 270 GRAD model code on the old switch gives a second check against the replacement.
• Homag fitment — Built as a spare part for Homag woodworking machines, it replaces the switch at the same mounting position.
• Signal path renewal — A new switch restores the position signal to the control, clearing faults caused by a worn contact.
• Mounting check — Before fitting, confirm the lever or cam moves within the 270-degree arc so the contacts trip at the set point.
• Cycle repeatability — With the actuator aligned to the 270-degree range, the switch trips at the same position on every machine cycle.
• Carrier options — Shipment is by DHL, FedEx, UPS, or similar, so the switch can be sent on the carrier you already use.
• Enquiry data — Send the machine model and part number 4008320091 with a photo of the old switch to confirm the item.

What changes on the shop floor when the right part goes back in:

• Restores the stop signal. A failed switch leaves the control without a position signal, so the cycle halts. Fitting the GC-UV 1 AV 1 270 GRAD puts that signal back at the point where travel is checked.
• Two identifiers to check. The part number 4008320091 and the model GC-UV 1 AV 1 270 GRAD both appear on the switch, giving the buyer two references to match before ordering.
• Arc matched to the machine. The 270-degree angle of operation defines the travel the switch is built to sense, so the actuator must be set within that arc for correct tripping.
• Repeatable trip point. When the lever or cam is aligned to the 270-degree range, the switch trips at the same position each cycle, keeping the machine sequence consistent.
• Fits the original position. As a spare part for Homag machines, it mounts where the old switch sat, so no change to the mounting arrangement is needed.
• Carrier choice. Shipment through DHL, FedEx, UPS, or similar lets the buyer route the switch on the carrier already used for machine parts.
• Clear enquiry path. Sending the machine model, part number 4008320091, and a photo of the old switch lets the item be confirmed before it is sent.

Match the part number 4008320091 and the model GC-UV 1 AV 1 270 GRAD to the switch on your machine. If both match the old switch, this is the replacement to order.

It means the angle of operation is 270 degrees. The switch is built to sense movement through that arc, so the lever or cam must travel within it to trip the contacts.

Yes, if the old switch shows 4008320091 or 4-008-32-0091. Send that number with your enquiry so the item is checked against it.

Read the model code on the old switch and compare it with GC-UV 1 AV 1 270 GRAD. A photo of the old switch sent with the enquiry helps confirm the match.

Check the mounting point and the actuator alignment. The lever or cam must move within the 270-degree range so the switch trips at the correct position.

Shipment is by DHL, FedEx, UPS, or similar carriers. Tell us which carrier you use when you send the enquiry.

No customisation is stated for this switch. It is supplied as the GC-UV 1 AV 1 270 GRAD limit switch with part number 4008320091.

Send the machine model, the part number 4008320091, and a photo of the old switch. These details let the correct item be confirmed before dispatch.