4-022-03-0201 4022030201 Homag Indicator TYP DA02-06-1.00-2-I D 10H7

When a Homag machine loses position feedback, parts drift out of alignment and cuts, shapes, or finishes come out wrong. The 4-022-03-0201 position indicator replaces the worn unit so the machine can report component position again. Without it, operators chase alignment errors instead of running production.

This is a position indicator, Homag part number 4-022-03-0201 or 4022030201, model TYP DA02-06-1.00-2-I with diameter D=10H7. It fits Homag woodworking machines as a spare part. To confirm the fit, check your machine's parts book for 4-022-03-0201 or 4022030201 and match the model and D=10H7 marking on the old indicator.

Before fitting, inspect the mounting bore for wear or damage that could affect the D=10H7 fit. The indicator must sit correctly to give accurate feedback on component position. A proper mount means alignment tasks stay precise, so cutting, shaping, and finishing run without position-related errors.

SHUNHONGYU supplies various woodworking machine parts for Homag machines. Packing and customisation are not stated here. When you enquire, send the part number 4-022-03-0201 or 4022030201, the model TYP DA02-06-1.00-2-I, and the D=10H7 size, plus a photo of the old indicator if possible. Supply comes from the same range as the rest of the catalogue.

What the specification fixes, and what it leaves to the machine:

• Position feedback — The indicator gives feedback on the position of machine components, which matters for tasks that need precise alignment and positioning.
• Model match — Model TYP DA02-06-1.00-2-I identifies the exact indicator type, so you can compare it with the marking on your existing unit.
• Bore fit — Diameter D=10H7 defines the fit in the mounting bore, and this tolerance class is intended for precise alignment applications.
• Homag spare — As a spare part for Homag woodworking machines, it replaces the original indicator when position feedback is lost or unreliable.
• Part number check — The Homag part number 4-022-03-0201 or 4022030201 lets you cross-check against the machine's parts book before ordering.
• Alignment use — Use it where component position must be reported accurately, such as setups that require exact alignment before cutting or shaping.
• Wear replacement — When the old indicator no longer holds position feedback, fitting this unit restores the feedback signal for alignment tasks.
• Installation check — Before mounting, check the bore for wear or damage, because the D=10H7 fit depends on a clean, undamaged mounting surface.
• Dust and vibration — Woodworking machines expose parts to dust and vibration, so the indicator is fitted in the machine where position feedback is needed.

What changes on the shop floor once the unit is in place:

• Restores position feedback. When the indicator stops reporting component position, alignment drifts and cuts suffer. Fitting 4-022-03-0201 brings position feedback back so operators can set up and run without chasing alignment errors.
• Exact model identification. The TYP DA02-06-1.00-2-I marking lets you compare the new indicator with the old one before installation. That reduces the chance of fitting the wrong unit and having to reorder.
• D=10H7 fit for alignment. A D=10H7 diameter is intended for precise fit in the mounting bore. That helps the indicator sit correctly, which matters when component position must be reported accurately.
• One number to check. Use Homag part number 4-022-03-0201 or 4022030201 against your parts book. A single cross-check confirms the indicator belongs on your machine before you commit.
• Fewer alignment rechecks. Accurate position feedback means less time spent rechecking alignment after setup. The machine reports where components are, so cutting, shaping, and finishing stay on track.
• Fits Homag woodworking machines. As a spare for Homag machines, the indicator goes where the original was mounted. That keeps the repair straightforward: remove the old unit, check the bore, fit the new one.