2032661700 Clamping Element SPZ 20 11 Homag Holzma Beam Saw Parts 2-032-66-1700

When a Holzma beam saw starts to slip or clamp unevenly, the clamp block is often the first wear point. A worn SPZ 20° 11mm element lets the clamping rail move under load, so cuts drift and the operator has to re-clamp.

The 2032661700 is a Homag clamping element with SPZ 20° 11mm geometry, type number 2-032-66-1700. It fits Homag woodworking machines and Holzma beam saw parts. Before ordering, confirm the old block carries the same 2-032-66-1700 or 2032661700 number and the SPZ 20° 11mm marking.

Check the mating rail and the block seat for scoring before you fit the new element. The SPZ 20° 11mm profile must sit square in the clamp housing; a burr or chip under the seat will tilt the block and wear one edge.

Supply is from Guangdong Province, China, with delivery place stated as Guangdong Province. Shipment is to be negotiated and can be arranged by the client or by the supplier. Send the machine model, the old part number 2-032-66-1700, and the SPZ 20° 11mm marking with your enquiry so the correct clamp block is picked.

The clamp block is a wear item on the Holzma beam saw. When it wears, the clamping rail loses grip and panel cuts move. Replacing the 2032661700 element brings the clamp back to its 20° 11mm seat.

What the specification fixes, and what it leaves to the machine:

• Clamp block fit — The SPZ 20° 11mm clamp block seats in the Homag clamping housing and holds the rail during saw carriage travel.
• Type number match — Marked 2-032-66-1700 and 2032661700, so you can match the old block before fitting.
• Beam saw use — Fits Holzma beam saw parts and Homag woodworking machines where the clamp rail is tensioned.
• Wear point — The 20° 11mm face is the contact surface; check it for scoring each time the rail is serviced.
• Companion block — The 2032655620 clamp block is also available for the same Holzma beam saw application.
• Installation check — Clean the block seat and remove burrs before fitting so the SPZ 20° 11mm profile sits square.
• Bolt torque — Tighten the mounting bolts evenly so the clamp pulls straight and the block wears evenly.
• Durability — Built for repeat clamping cycles on the beam saw, the block holds its 20° 11mm geometry in use.
• Replacement decision — Replace the block when the rail slips or cuts drift, rather than re-clamping through a shift.
• Ordering detail — Quote SKU 2-032-66-1700 with the SPZ 20° 11mm marking so the right element is supplied.
• Specified characteristic — competitive Price.

What changes on the shop floor when the right part goes back in:

• Restores clamp grip. A fresh 2032661700 block puts the SPZ 20° 11mm face back against the rail, so the saw carriage clamps without slipping and cuts stay on size.
• Simple fit check. The type number 2-032-66-1700 and the SPZ 20° 11mm marking let you confirm the block against the old one before the machine is opened.
• One wear point solved. Replacing the clamping element addresses the slip that shows up as drifting cuts, instead of adjusting the fence or re-clamping every panel.
• Companion part on hand. The 2032655620 clamp block is also available, so a rail service can cover both blocks in one enquiry and one shipment.
• Durability in cycles. The element is made for repeat clamping on the Holzma beam saw, holding its 20° 11mm seat through production shifts rather than one job.
• Competitive price. The block is offered at a competitive price, which keeps the spare-parts cost per beam saw service down for the shop.
• Clear ordering. Send the machine model, 2-032-66-1700 and the SPZ 20° 11mm marking with your enquiry, and shipment can be negotiated to suit your schedule.

It fits Homag woodworking machines and Holzma beam saw parts. The 2032661700 element is the SPZ 20° 11mm clamp block for that application.

Match the type number on the old block. Look for 2-032-66-1700 or 2032661700 and the SPZ 20° 11mm marking before ordering.

Yes, the 2032655620 clamp block is also available. Ask for it with the 2032661700 element if your rail service needs both.

It identifies the clamp profile. The 20° 11mm face must seat square in the housing, so check the old block carries the same marking.

Check the block seat and mating rail for burrs or scoring. A clean seat lets the SPZ 20° 11mm profile sit flat and wear evenly.

Replace it when the rail slips or cuts drift under clamp load. A worn 20° 11mm face is the usual cause on the beam saw.

Shipment is to be negotiated. Delivery place is Guangdong Province, China, and shipping can be arranged by the client or by the supplier.

Send the machine model, the old part number 2-032-66-1700, and the SPZ 20° 11mm marking. That lets the correct element be picked for your saw.