3-011-22-6760 3011226760 CONNECTION PK VERSTELLUNG For Homag Woodworking Machine

When an adjustment on a Homag machine stops holding, the connection between the adjuster and the moving part is usually the first thing to pull. Play at that joint turns a setting that should stay put into one that drifts between cycles. Replacing the worn connector restores the link between adjustment and movement.

CONNECTION PK VERSTELLUNG is a metal connector, part number 3-011-22-6760, also written 3011226760. It is a woodworking machine part for Homag equipment, used where the machine's adjustment connects to the moving assembly. A buyer confirms fit by matching 3-011-22-6760 or 3011226760 against the number on the existing part or in the machine's parts documentation.

Check the mating faces and the fixing points at both ends of the joint before installation. A connector that seats cleanly at both ends takes the adjustment load without slop, so the setting you dial in stays where you put it through the run. Any play left in the joint will show up as drift.

Parts ship in a standard carton box by DHL, FedEx, UPS or similar. Send the machine model, the number 3-011-22-6760 or 3011226760, and a photo of the old connector with your enquiry so the fit is confirmed before dispatch. State the quantity you need.

What the specification fixes, and what it leaves to the machine:

• Adjustment linkage wear point — Connects the adjustment to the moving assembly, so wear shows as play and drift instead of a setting that holds.
• Number matching for fit — Match 3-011-22-6760 or 3011226760 against the existing part or the machine's parts documentation to confirm the fit.
• Metal body under load — The connector is metal, so it takes the adjustment load at the joint rather than flexing like a softer material.
• Two number formats — The same connector carries 3-011-22-6760 and 3011226760, so either number on a parts list points to it.
• Drift diagnosis — Play at this joint is a common cause of an adjustment that will not hold, which makes it a first check.
• Seating check before install — Check the mating faces and fixing points at both ends so the connector seats cleanly before you tighten it.
• Homag machine fitment — Fits Homag woodworking machines as a connection and connector part, ordered by the Homag number on the machine.
• Carton box packing — Ships in a standard carton box, which keeps the connector protected in transit before it reaches the machine.
• Courier shipment — Ships by DHL, FedEx, UPS or similar, so the connector arrives as a tracked parcel to your address.

What changes on the shop floor once the unit is in place:

• Stops adjustment drift. A connector that seats cleanly at both ends holds the setting through the run, so operators spend less time re-dialling the same adjustment between cycles.
• One number to order. Because 3-011-22-6760 and 3011226760 both identify the same connector, either number on the parts list is enough to place the order.
• Fits the adjustment joint. As a metal connection for Homag machines, it takes the load where the adjustment meets the moving assembly instead of flexing at the joint.
• Faster fault finding. When a setting will not hold, checking this joint first rules in or out the connection before you strip the surrounding assembly.
• Protected in transit. Packed in a standard carton box and shipped by DHL, FedEx, UPS or similar, the connector arrives as a parcel you can track.
• Simple install check. Check the mating faces and both fixing points before tightening; a clean seat means the adjustment load passes through without slop.
• Right part first time. Send the machine model and the old part number with your enquiry so the connector is checked against your machine before dispatch.

Match 3-011-22-6760 or 3011226760 against the number on the existing connector or in your machine's parts documentation. Send the machine model and a photo of the old part with your enquiry so the fit is confirmed before dispatch.

It links the adjustment to the moving assembly. When that link wears, the setting drifts instead of holding, so the connector is the joint to check first.

Play at the connection between the adjuster and the moving part is a common cause. Check the mating faces and both fixing points at this joint before you look further into the assembly.

Yes. 3-011-22-6760 and 3011226760 both identify this connector, so either number on a parts list points to the same part.

It is metal. That lets it take the adjustment load at the joint rather than flexing under it.

It ships in a standard carton box by DHL, FedEx, UPS or similar, so it arrives as a tracked parcel.

Send the machine model, the number 3-011-22-6760 or 3011226760, the quantity you need, and a photo of the old connector. That lets the fit be checked against your machine before dispatch.

Yes. State the quantity you need with the enquiry, along with the part number and machine model, so the order is confirmed against your machine.