3005071560 Universal Joint Shaft Homag Spare Part Cardan Shaft 3-005-07-1560

When a universal joint shaft wears on a Homag machine, the symptom is often vibration or lost motion in the feed or transfer section. The joint's cross and bearings take the load, and once play develops, power transmission becomes uneven. Replacing the shaft with the correct 147 mm length restores smooth drive without altering adjacent components.

This cardan shaft is a metal universal joint with a 20 mm outer diameter and 14 mm inner diameter, finished in black. It fits Homag woodworking machines that use the 3005071560 or 3-005-07-1560 reference. Confirm fit by checking your machine's parts manual for that number and measuring the old shaft's 147 mm length and bore diameters.

Check the joint's mounting orientation and the condition of the mating yokes before installation. The 20 mm outer and 14 mm inner diameters must seat correctly on the shaft ends. Any wear on the yokes will shorten the new joint's life, so inspect and replace worn mating parts at the same time.

Supply is straightforward: the part is a metal universal joint in black. No customisation or packaging details are stated. When enquiring, send the machine model, the part number 3005071560 or 3-005-07-1560, and the measured length and diameters from your old shaft so the supplier can confirm the match.

What the specification fixes, and what it leaves to the machine:

• Length match for direct replacement — The 147 mm length allows the shaft to drop into the same space as the original, so you avoid modifying mounts or adjacent drive parts.
• Outer diameter for yoke fit — A 20 mm outer diameter seats correctly in the yoke bore, keeping the joint centred and reducing vibration during rotation.
• Inner diameter for shaft engagement — The 14 mm inner diameter matches the mating shaft end, ensuring full contact and even load transfer across the joint.
• Metal construction for wear resistance — Metal construction gives the joint the strength to handle repeated load cycles in daily woodworking production without early deformation.
• Black finish for shop-floor visibility — The black finish makes the joint easy to spot during inspection, helping you identify wear or looseness before it causes a breakdown.
• Homag compatibility reference — Using the 3005071560 or 3-005-07-1560 number lets you cross-check against the machine's parts list before ordering.
• Universal joint action for angle drive — The universal joint design accommodates misalignment between shafts, which is common in feed and transfer mechanisms on Homag machines.

What changes on the shop floor when the right part goes back in:

• Restores smooth power transmission. A worn joint causes vibration and lost motion; fitting the correct 147 mm shaft brings drive back to a steady state, so downstream operations run without chatter.
• Reduces unplanned downtime. Keeping this 3005071560 joint in maintenance stock means you can replace a failed unit during the shift instead of waiting for a delivery.
• Simplifies fitment checks. The 20 mm outer and 14 mm inner diameters give you two quick measurements to compare against the old part before installation.
• Extends the life of mating parts. A joint that fits correctly at 147 mm length puts less stress on yokes and bearings, so adjacent components wear at a normal rate.
• Cuts guesswork from ordering. Using the Homag reference 3-005-07-1560 on the enquiry lets the supplier confirm the part against your machine model.
• Supports routine maintenance planning. With a known wear point at the cross bearings, you can schedule inspection and replacement before vibration affects finished work.
• Keeps spares inventory simple. One metal joint in black covers the drive link; you avoid stocking multiple variants and reduce the risk of picking the wrong part.

Check your machine's parts list for 3005071560 or 3-005-07-1560, then measure the old shaft's 147 mm length and 20 mm/14 mm diameters to confirm.

The joint is 147 mm long, with a 20 mm outer diameter and a 14 mm inner diameter, made of metal in black.

This is a replacement spare part for Homag machines; it carries the 3005071560 and 3-005-07-1560 reference numbers for cross-checking.

The universal joint is made of metal and finished in black, giving it the strength for repeated load cycles in woodworking machinery.

Fit the 20 mm outer diameter into the yoke and the 14 mm inner diameter onto the shaft end, then check the mating yokes for wear before tightening.

Inspect the yokes and bearings for play or wear; a worn yoke will shorten the life of the new 147 mm joint even if it fits correctly.

Yes, the part is supplied as a single universal joint; no minimum order or packaging details are stated, so confirm with the supplier when enquiring.

Send the machine model, the part number 3005071560 or 3-005-07-1560, and the measured length and diameters from your old shaft.