Manual Lubrication Pump Hand Operated Oil Pump 4mm 6mm Brass Fittings Edge Banding Machine Guide Rail Lubrication Y-8 Y-6

Need to oil the guide rails and chains on an edge bander without wiring anything into the machine? The Y-8 hand-operated pump does it with one lever press. Plunger type manual pump, die cast aluminum body, brass outlet for 4mm or 6mm oil tubes, transparent oil level window, right-side or double-side outlet. No motor, no cable and no control box. Three series — Y-8, Y-6 and LSG — cover edge banding machines, CNC routers, machine tools and punch presses, and one body feeds rails, chains and lead screws. Price negotiable.

A shop running edge banders, routers, machine tools or punch presses meets the same three problems at the oil points: guide rails and chains run dry because the oil can is never where the machine is, an electric pump adds wiring and a failure point to a machine that had none, and nobody sees the oil level until a rail starts to score. The Y-8 hand pump clears all three with one lever press.

It is a plunger type manual pump in die cast aluminum, supplied as three series — Y-8, Y-6 and LSG — so the body that already sits on the machine can be matched. Oil goes to guide rails, chains, lead screws and cutter spindles at the interval the operator picks. No timer, no solenoid, no controller.

The outlet is brass and takes 4mm or 6mm oil tubes. Direction is chosen at the order: right side for a single line, double side for two lines off one body. A transparent oil window shows the level without opening anything — the check that keeps a guide rail out of trouble.

The body is a silver-grey die cast aluminum casting, described as corrosion resistant. Fitment covers 4 machine families — edge banding machines, CNC routers, machine tools and punch presses. Packing is a standard export carton with foam protection, customized on request; OEM/ODM accepted. Price negotiable.

What the pump does, in the numbers that matter at the machine:

• One lever, no wiring — the black top handle drives a plunger: press or rock it and oil is discharged, with 0 electrical parts and 0 wires.
• Die cast aluminum body — one silver-grey casting, described as corrosion resistant, for the frame where coolant and chips collect.
• Two tube sizes — the brass outlet takes 4mm or 6mm oil tubes, so the line already on the machine is reused.
• One or two outlets — right side for a single line, double side for 2 lines from one body.
• Oil level in sight — the transparent window shows the remaining oil; the check is a glance, not a disassembly.
• Three model series — Y-8, Y-6 and LSG share the lever-and-plunger layout, so a bracket already on the machine can be matched.
• Four oiling points — guide rails, chains, lead screws and cutter spindles, fed from one body.
• Four machine families — edge banding machines, CNC routers, machine tools and punch presses.
• OEM/ODM and packing — a standard export carton with foam protection, customized to the order; OEM/ODM accepted.

The choice at a dry rail is an electric pump with wiring, or a lever somebody presses by hand. This is the second one, and it keeps the cost of the first one off the machine.

• No electrician on the install. There is no cable, no terminal and no control box — the pump mounts, the tube goes on, the operator presses the lever.
• The oil goes where you point it. One body feeds guide rails, chains, lead screws or cutter spindles, in the order the machine needs them.
• Match the fitting you already have. 4mm and 6mm tubes are both accepted, and the outlet can be right side or double side at the order.
• A level check costs a glance. The transparent window shows remaining oil, so a refill is planned instead of discovered at a scored rail.
• One spare covers a family. Y-8, Y-6 and LSG share the layout, so one stock item can serve more than one machine on the floor.
• A body that survives the shop. Die cast aluminum casting, silver grey, with the brass outlet sitting at the wear point.
• Your label, your carton. OEM/ODM is accepted and packing is customized on request, so the pump arrives ready to stock or to sell.

No. It is a plunger type manual pump driven by the black top handle — press or rock the lever and oil is discharged, with no motor, no cable and no control box.

Both 4mm and 6mm. The brass outlet accepts either size, so the oil line already on the machine is reused instead of replaced.

Yes, if the machine mounts a hand pump on the frame. It is listed for edge banding machines, CNC routers, machine tools and punch presses, in three series (Y-8, Y-6, LSG) to match the bracket.

Either. Right side gives a single line, double side gives 2 lines from one body, and the direction is fixed when the order is placed.

Send the model on the machine's parts list, or a photo of the old pump. The three series share the lever-and-plunger layout, and the match is confirmed before the order is quoted.

Through the transparent oil window. The level is visible from outside, so a top-up is planned at the interval instead of found at a scored rail.

Die cast aluminum, silver grey, described as corrosion resistant. The outlet is brass, which is the part that meets the oil line.

Yes. OEM/ODM is accepted, and packing is a standard export carton with foam protection or a carton customized to the order.