Edgeband Feeding Unit with Servo Motor Intelligent Servo Driven Edgeband Feeder

Tired of stopping the edgebander every time the tape colour changes? The XE6SD-A holds six tape rolls on one servo-driven feeding unit and switches between them by selection instead of re-threading. Tape thickness 0.3-3 mm, feed speed 0-30 m/min, panels 10-60 mm, working air pressure 0.2-0.6 MPa, body L565 x W490 x H365, mounted on the edgebanding machine base. One unit covers the whole colour range of a custom furniture line.

A line that runs one tape colour at a time pays for every changeover: the operator stops the conveyor, cuts the old strip, threads the new roll, then re-checks the joint before the first panel reaches the gluing station. On a shift carrying four decor colours that cycle repeats dozens of times, and each repeat is dead time on the outfeed. The XE6SD-A removes the cycle.

The XE6SD-A is an intelligent, servo-driven six-channel edgeband feeding unit. It mounts on the edgebanding machine base and holds six tape rolls at once, so the next colour is already threaded. A servo axis tracks line speed across 0-30 m/min and controls the length actually fed, so strip is cut to the panel rather than to a timer. Tape thickness spans 0.3-3 mm on one head.

The feed is rated for 10-60 mm panels and runs on compressed air at 0.2-0.6 MPa, the pressure a standard edgebander already supplies. Cutting uses a swing-type flexible head with a fast reciprocating stroke, so the strip is sheared clean rather than torn.

Rubber-coated feed rollers and a height-limiting guide hold the strip against the line and keep the visible face free of roller marks. The body measures L565 x W490 x H365, small enough to sit on the machine base without a separate frame or extra floor space.

What the unit adds to a standard edgebander, in numbers.

• Six tape channels, one-touch switching - up to 6 rolls sit on the storage rack; the next colour is a selection, not a manual re-thread.
• Servo feed locked to line speed - 0-30 m/min range with the fed length set at the axis, so strip is metered to the panel instead of running on a fixed cycle.
• Tape thickness 0.3-3 mm - the same head feeds thin 0.3 mm PVC and full 3 mm stock, so no roller change between a drawer front and a worktop edge.
• Panel thickness 10-60 mm - cabinet sides, shelves and build-ups pass on one setting, the working range of custom furniture.
• Swing-type flexible cutter - a fast reciprocating shear stroke cuts the strip cleanly: no chipping, no jamming, no tape tearing.
• Rubber-coated feed rollers - grip the strip without marking it, so the visible face keeps the finish it had before the pass.
• Height-limiting guide - holds the strip at the set height and stops narrow tape from climbing or wandering on the line.
• Working air pressure 0.2-0.6 MPa - driven from the air line the edgebander already has, with no extra pressure setting to chase.
• Base-mount footprint L565 x W490 x H365 - bolts to the edgebanding machine base; no separate stand, no extra floor space.

A shop that needs multi-colour edging has two options: send the batches out, or keep stopping the line. This unit is the third one.

• No stop for a colour change. With 6 tapes loaded, switching is a selection at the unit, so the conveyor keeps running and the panel spacing on the line is not disturbed.
• Tape cost follows the panel, not the timer. A servo axis sets the fed length for each panel across 0-30 m/min, and the published figure for the six-channel rack configuration is up to 30% less tape consumed.
• One unit instead of six spools on the floor. Six rolls, one L565 x W490 x H365 body on the machine base, so the aisle stays clear and nobody walks off to find the next colour.
• End cuts you can hand to a customer. The swing cutter shears the strip instead of tearing it, which is the difference between an edge that passes final inspection and one that has to be re-trimmed.
• Fits the machine you already run. Base mounting plus 0.2-0.6 MPa shop air means the installation is mechanical, and the 0.3-3 mm tape window covers a mixed order book.
• Predictable to quote on. Because tape 0.3-3 mm and panels 10-60 mm are both published ranges, you can price a job from the drawing without measuring a sample first.

Six. The unit holds up to 6 tape rolls on the storage rack and switches between them by one-touch selection, so a multi-colour run does not need the line to stop for a re-thread.

0.3 mm to 3 mm. That covers thin PVC edging up to full 3 mm stock, and the same head handles both, so you are not changing rollers between product families.

0 to 30 m/min. The servo axis matches the feed to the line speed and sets the length actually fed, so the strip is cut to the panel rather than to a timed cycle.

Yes, if your machine has a free position on its base. The unit's mounting position is the edgebanding machine base, at L565 x W490 x H365, and it runs on the shop air line at 0.2-0.6 MPa.

10 mm to 60 mm. Cabinet sides, shelves and thicker worktop build-ups all pass on the same setting, which is the range custom furniture actually uses.

0.2 MPa to 0.6 MPa. That is inside the working pressure a standard edgebander already supplies, so no separate pressure setting has to be chased on the shop floor.

No. Feeding is done by rubber-coated rollers backed by a height-limiting guide, so the strip is held on the line without the visible face picking up roller marks.

Up to 30% in the six-channel rack configuration, the figure published for that setup. The saving comes from servo metering the fed length per panel instead of running a fixed cycle.