Manual Control Glue Pot for KDT Edgebander Woodworking Edgebanding Machine Part

A failed glue pot on a KDT edge bander should not cost a week of waiting. XEISD-B is the manual control glue pot — the glue tank that sits in the edge banding unit of KDT machines and feeds the glue roller. Control is a hand lever, so there is no control board to diagnose. A pneumatic version is available as an alternative, and this model is supplied without dust removal. Pot spares are stocked separately, so a worn lever does not need a second complete pot. Price by inquiry; shipped by DHL, FedEx or UPS.

A glue pot that stops feeding shows up as a dry band a metre into the panel, a hand roller for the rest of the shift, and a call to an agent who may not carry the part. The second problem is the label: the failed pot has usually lost it, so the buyer matches photos against three near-identical castings.

XEISD-B is the manual control glue pot for KDT edge banding machines, the glue tank that feeds the glue roller. It arrives as the assembly in the photos: pot body, hand lever with rubber boot, two ball-knob levers at the outlet, one perforated heater cover, a pre-wired cable with plug, and a bolted bracket with slotted holes. No control board, so nothing is diagnosed through a screen.

Control is manual: the operator opens and closes the glue outlet at the lever. A pneumatic version is also available where the line actuates the pot itself. This model carries no dust removal, 0 extraction components, so a shop that already runs a hood is not sold a second one.

The pot is produced in China for KDT machines. Price is quoted per inquiry, because the manual and pneumatic versions are not priced the same. Orders move by DHL, FedEx or UPS, and pot spares are stocked separately, so a worn lever does not force a second complete pot.

Each line below can be checked against the pot on your machine:

• Manual control, no electronics — one hand lever with a rubber boot opens and closes the glue outlet; there is no controller to diagnose and no sensor to fail.
• Pneumatic version available — where the machine actuates the pot itself, the pneumatic version covers it; the manual XEISD-B is the version in these photos.
• Bracket and lever match KDT — the mounting plate and lever position follow the glue pot mounting on KDT edge banding machines.
• No dust removal function — 0 extraction parts are supplied with this model; it is the plain glue pot, paired with an existing hood.
• Two ball-knob levers at the outlet — the glue block at the nozzle end is worked by hand from 2 points, close to where the glue leaves the pot.
• Pre-wired cable and plug — the harness leaves the heater cover as one lead, so the pot plugs into the existing connection instead of being re-terminated on site.
• Perforated heater cover — 1 vented cover shields the hot face and lets heat escape away from the cable run.
• Bolted bracket with slotted holes — the plate bolts to the unit and the slots take up alignment without redrilling.
• Spares stay orderable — levers, heater parts and pot spares can be bought without a second complete pot.

The usual choice is between a service visit and a pot that arrives with the wrong control version. XEISD-B takes the second risk out and shortens the first:

• The control version is named on the part. Manual or pneumatic is the first thing to get wrong, and the manual pot carries its own item number, XEISD-B, so the order and the machine agree.
• No dust module paid for twice. 0 extraction parts are included, so a shop that already runs a hood buys the pot only, not a second hood with it.
• A repair, not a rebuild. Body, lever, heater cover and bracket arrive as one assembly, so the unit goes back together in one fit instead of a parts hunt.
• One line item for the whole unit. pot, cable with plug, bracket and both outlet levers are ordered once, not as 4 separate parts that may not meet.
• Hand control where the glue leaves. the lever sits on the pot body and 2 ball knobs sit at the outlet, so feed is adjusted at the nozzle, not from arm's length.
• Small shipment, no forwarder. DHL, FedEx and UPS are all used, so one pot moves as a parcel and pot spares can follow on the same account.

KDT edge banding machines. The pot is listed for KDT edgebanders; check the bracket and lever position on the failed pot against the photos before ordering.

Manual. XEISD-B is the hand-lever glue pot. A pneumatic version is also available where the machine actuates the pot itself, and it is quoted separately.

No. This model is supplied without dust removal, so 0 extraction components come in the kit. Pair it with an existing hood if the line is already ducted.

The complete manual control pot assembly shown in the photos: pot body, hand lever with boot, 2 outlet ball knobs, perforated heater cover, cable with plug and the mounting bracket.

Yes. Glue pot spares are stocked separately, so a damaged lever or a failed heater part does not require a second complete pot.

By hand, at the lever. The operator opens and closes the glue outlet with the hand lever on the pot body, and the 2 ball knobs at the outlet are worked at the nozzle.

Price is quoted per inquiry, because the manual and pneumatic versions are priced separately. Send the machine model and quantity for a quote.

By express — DHL, FedEx or UPS, whichever is the cheaper for the destination, with air and sea used for larger spare-parts orders.