132X54X48 Vacuum Cup 1/3 Size Plastic Biesse CNC Machining Center Spare Parts

Need a pod that keeps a panel flat on a Biesse nesting table without re-levelling the grid? The 132X54X48 vacuum cup is the 1/3 size body: 132 mm long, 54 mm across the top face and 48 mm tall, moulded in PF (phenol formaldehyde) plastic. Brown is standard and grey is also produced. The same 132 x 54 mm top face is available at 29 mm and 74 mm heights, so a mixed row of pods can go back to one matched set. Seal, ball valve and locating ring are listed as separate accessories. Price quoted per order.

A nesting table goes out of true three ways. One pod stops sealing and the panel lifts a fraction of a millimetre mid-cut. A replacement cup arrives off the height of the body it replaces, so the grid is re-levelled. Mixed heights from earlier repairs then mean no vacuum level holds a panel flat. The 132X54X48 vacuum cup targets all three.

It is a single replacement pod for Biesse CNC machining centres, 1/3 size: 132 mm long, a 54 mm top face, a 48 mm body. PF phenol formaldehyde plastic is a moulded thermoset, so it holds that 132 x 54 mm section under vacuum instead of drawing inward like a soft cup, and the seal line stays on the perimeter the block was set to.

The 48 mm height is the figure that decides fit. The same 132 x 54 mm top face is also produced at 29 mm and 74 mm, so one order covers shallow and deep positions, and a worn row returns to matched heights instead of a shim under a body.

Brown is standard, grey is also available. Seal, ball valve and locating ring are separate accessories, so a pod is re-sealed alone or built up complete. Customization is supported, and the part is produced in China.

The numbers that decide whether a cup seats on your table:

• 132 x 54 mm top face — the footprint that has to match the seat in the block; 54 mm is the 1/3 size width.
• 48 mm body height — the dimension that sets how far the panel sits above the block; 29 mm and 74 mm share the same top face.
• PF phenol formaldehyde — a moulded thermoset, so the 132 x 54 mm section holds under vacuum instead of collapsing inward like a soft cup.
• Brown standard, grey available — two colours of one part, a usable table map when pods of different heights sit together.
• Seal, ball valve, locating ring — three accessories listed separately, so a pod is re-sealed on its own or assembled as a complete unit.
• 1/3 size for small workpieces — a 54 mm top face that fits between clamps and beside small parts where a full-length pad cannot.
• Listed as a Biesse CNC spare — a body for the vacuum block on Biesse CNC centres; fit is checked on the top face and the height.
• Customization, and one cup at a time — a non-standard height or colour is produced to order, and pods are supplied per position, not in sets.

The choice on a worn pod is between running it until a panel slips and buying a box when you need two.

• A level row again, not a shim. With 29 mm, 48 mm and 74 mm bodies on one 132 x 54 mm top face, a worn position goes back at the height the grid was levelled to.
• A thermoset keeps its section. PF plastic holds shape under vacuum, so the seal line stays on the 132 x 54 mm perimeter instead of pulling in like a soft cup.
• Small parts stop being skipped. The 54 mm top face reaches between clamps and holds workpieces a full-length pad cannot, so small runs stay on the table.
• A crack costs one part. Supplied singly, so one damaged position is one replacement rather than a set of pods for the whole table.
• Accessories on the same order. Seal, ball valve and locating ring are listed with the cup, so a complete unit arrives instead of a body waiting for a gasket.
• Colour marks the layout. Brown and grey give two markers on one table, so the 48 mm positions stay identifiable after a mixed set of repairs.
• Custom height without a new setup. Customization is supported, so a non-standard body is produced to order instead of the table being re-levelled around a stock part.

Only if your table uses the 132 x 54 x 48 mm position. The cup is listed as a spare for Biesse CNC machining centres, but the top face is fixed at 132 x 54 mm and the body at 48 mm, so check both against the pod you are pulling off.

It is plastic, PF phenol formaldehyde. Being a thermoset matters under vacuum: the 132 x 54 mm section stays as moulded instead of drawing inward the way a soft rubber cup does.

It is the size designation for this narrow pod, not a measurement. The numbers to fit are the 132 x 54 mm top face and the 48 mm height; 1/3 size is how this body is listed in the range.

Yes. The same 132 x 54 mm top face is also produced at 29 mm and 74 mm, and customization is supported for a non-standard height or colour.

No. It is supplied as a single replacement pod, so a cracked position is a one-part order and the rest of the table keeps its levelled height.

Nothing more is included; the seal, ball valve and locating ring are listed as separate accessories. Add them to the same order if the worn pod is being rebuilt rather than just re-bodied.

No. Brown is standard and grey is also available, and both are the same PF part at 132 x 54 x 48 mm; colour is a visual marker on the table.

Measure the old body from the block face to the top face; it should read 48 mm. A reading of 29 mm or 74 mm means you need that height instead, on the same 132 x 54 mm top face.