Vacuum Suction Cups 132x146x29mm Pods For Biesse Rover CNC Machining Center

Need a vacuum pod that holds a panel flat on a Biesse Rover table? The 132x146x29mm Biesse vacuum block clamps flat panels through the machine's own vacuum circuit. It measures 132 x 146 mm across the base, stands 29 mm tall and weighs 1 kg, moulded in premium Bakelite in brown or grey. A locating ring and a foam strip are available with it, other sizes are available, and customisation is supported. Price is quoted on request.

Three things stop a nested CNC table, and all three start at the vacuum pod. A pod whose sealing face has worn leaks air, the panel creeps a few tenths of a millimetre, and the part is scrapped at the last operation. A pod that has collapsed no longer measures 29 mm, so the Z datum moves and every pocket cuts shallow. Ordering one block at a time leaves the machine standing while the paperwork moves.

The 132x146x29mm vacuum block is the Bakelite suction cup that clamps flat panels on a Biesse Rover CNC machining centre through the machine's own vacuum circuit. The base measures 132 x 146 mm, the stack height 29 mm, so the block sits in the table positions the Rover control already knows. Each weighs 1 kg.

The body is moulded in premium Bakelite, a thermoset that cures hard and keeps its shape under vacuum load. Brown is standard and grey is available, for shops that code pods by size or table. Because the body holds its 29 mm height, the Z datum repeats from fixture to fixture instead of being re-set.

A locating ring and a foam strip are available, so the sealing face can be renewed without replacing the 1 kg body. Other sizes are available, and the block can be customised to your size and colour. Price is quoted on request.

What separates this block from a generic suction cup is the material, the stack height, and the fact that its wear parts are sold on their own.

• Rover table footprint - 132 x 146 mm at the base and 29 mm tall, matched to the vacuum block positions on Biesse Rover tables.
• Bakelite body - a moulded thermoset rather than a soft rubber cup, so the 29 mm stack height is held under vacuum load.
• 1 kg per block - heavy enough to seat by hand and to stay seated while the vacuum is pulled.
• Two colours - brown as standard and grey also available, both from the same mould, so pod sets can be coded by size or table.
• Locating ring available - centres the cup on the block, so the sealing face lands square in the 132 x 146 mm position.
• Foam strip available - renews the sealing face without buying another 1 kg Bakelite body.
• Other sizes available - the 132 x 146 x 29 mm block is one size in the range; state your dimensions on the enquiry.
• Customisation supported - size, colour and accessory set can be built to the specification you send.
• Built for flat panels - the cup is made to hold panels on a nesting table, which is what a Rover runs all day.

If the machine is already standing in the shop, the real choice is rarely between two pods; it is between a spare on the shelf and a Rover that has lost vacuum mid-panel.

• A repair measured in minutes. The block is a 1 kg part that sits in a table position: lift the old one out, seat the new one, renew the foam strip, and the table is pulling vacuum again.
• Depth that repeats. Because the Bakelite body holds its 29 mm height, the Z datum stays where it was set and pockets cut to the programmed depth on the first panel and on the hundredth.
• Wear goes where the wear is. The foam strip and the locating ring take the abrasion and are available as separate items, so the 1 kg body stays in service instead of being thrown away with the seal.
• A pod set you can read at a glance. Brown and grey mouldings let a shop code a size or a table by colour, with no labels to fall off.
• Room to grow. Other sizes are available and customisation is supported, so the second and third Rover are covered without opening a new part number.

Biesse Rover CNC machining centres. The 132 x 146 mm base and the 29 mm height match the vacuum block positions on a Rover nesting table.

132 x 146 mm across the base, 29 mm tall, 1 kg in weight.

Premium Bakelite. It is a moulded thermoset, which is why the 29 mm stack height is held under vacuum load.

No. A locating ring and a foam strip are available separately, so the sealing face can be renewed and the Bakelite body kept.

Yes. Brown is the standard colour and grey is also available.

Yes. The 132 x 146 x 29 mm block is one size in the range; send the dimensions you need and the quote is built against them.

Yes, customisation is supported. Size, colour and the accessory set can be built to the specification you send.

Send the size, colour and accessories you need and the price is quoted on request, because one enquiry can cover block, locating ring and foam strip together.