132X54X74mm Vacuum Suction Pods For Biesse Rover PTP CNC Machining Center

Need to hold a part clear of a Biesse Rover flat table without re-fixturing it? This 132 × 54 × 74 mm vacuum pod sits on the machine's existing grid and holds solid wood or edge-detail work 74 mm above the table. Rubber pads on the top face grip the part, a gasket ring on the base seals against the grid, and the same footprint is built in 48 mm and 29 mm heights when 74 mm is too tall. It is a wear part, not a machine: drop it in, switch the vacuum on, cut.

Shops running a Biesse Rover or a Point-to-Point machine hit the same three things: pods worn flat, so the sheet creeps under the cutter; a pod stack at the wrong height, so a short tool never reaches the edge detail; and the one size that would fix the job missing from the store. A fourth follows — waiting for the replacement to arrive.

This is that missing size. The pod is 132 × 54 mm across the top face and 74 mm tall, a direct replacement for the block under a Biesse Rover. The part sits on the top face and the body holds it clear of the table, so a tool can cut the edge all the way round and through the full thickness without touching the grid.

The same 132 × 54 mm footprint is also built in 48 mm and 29 mm, so a thick stack or a thin one is bought rather than shimmed, and one spare line covers three setups.

The body is grey plastic, with brown also produced. It is sold as a spare for Biesse Rover and PTP machining centres, ships from China in 1 to 7 work days, and leaves by air, sea or express. Where a parts list shows AS24M00075, that reference is available too.

What separates a pod that bolts on from one that costs a shift:

• 132 × 54 mm top face — sized to the Biesse pod position, so it drops in and out with no adaptor plate.
• 74 mm of lift — the part sits clear of the grid, so an edge cut runs all the way round and through the thickness.
• Three heights, one base — 29 mm, 48 mm and 74 mm share the 132 × 54 mm footprint, so one spare covers thin and thick stock.
• Grey plastic body — one-piece moulding, one colour code in the store, no rust film to clean off.
• Rubber pads on the contact face — they grip the part and are sold separately, so a spent pad does not scrap the block.
• Gasket ring on the base — the ring seats vacuum against the grid, and gaskets are a separate replacement item.
• Centre bore for the fixing — the machine's own screw passes through the top face, so no hardware is added.
• Full, half and one-third sizes — full-size from 145 × 135 × 48 mm to 146 × 131 × 74 mm, half-size 75 × 135 × 48 mm, one-third 50 × 135 × 48 mm.
• Alternative reference AS24M00075 — that number is available on the same order where a parts list calls it up.

The choice is usually to keep one pod size and pack the work up to height, or to keep a spare on the shelf. The second one costs less the first time a tool touches the table.

• A spare on the shelf, not on a ship. A worn pod stops a machine; three heights in the store keep the setup running while the replacement travels, at a lead time of 1 to 7 work days.
• Edge work without re-fixturing. 74 mm of lift is enough to run a cutter under the part, so the job is cut once instead of being taken off, packed up and set again.
• One inventory line, three setups. 29 mm, 48 mm and 74 mm share the 132 × 54 mm base, so a single part number covers three stock thicknesses.
• The wear part is the pad, not the pod. Pads and gasket rings are separate items, so a spent grip costs a pad instead of a whole 132 × 54 × 74 mm block.
• Small parts get their own zone. Half-size 75 × 135 × 48 mm and one-third 50 × 135 × 48 mm pods let a full grid be sectioned, so vacuum is not wasted on open table.

Biesse Rover and Point-to-Point CNC machining centres. It replaces the vacuum block under the work on a 132 × 54 mm footprint, so it goes on the grid the machine already has.

No. The same 132 × 54 mm footprint is also built in 48 mm and 29 mm. Pick the height by the stack you need under the part, not by the size of the pod you happen to own.

No. The rubber pads and the base gasket ring are sold as separate replacement parts. If the body is sound, a pad change brings the grip back.

Both. Because the body raises the part off the table, solid wood and edge detail can be cut with 74 mm of clearance under the tool, which flat-cup setups do not give.

Check AS24M00075. That reference is also available and does the same job; order against whichever number your machine's list carries.

With the machine's own fixing screw, through the centre bore in the top face. No adaptor plate and no drilling, so the grid is not modified.

1 to 7 work days from order. Goods leave China by air, by sea or by express, and the method is chosen to the order quantity; freight is quoted once the destination port is known.

Yes. Full-size runs from 145 × 135 × 48 mm to 146 × 131 × 74 mm, half-size from 75 × 135 × 48 mm, and one-third size from 50 × 135 × 48 mm; sizes outside the list are made to order.