CNC Machine Biesse Spare Parts Vacuum Suction Cup H48mm TOP 132x54mm

Need the grey pod that holds panels flat on a Biesse nesting table? This bakelite vacuum suction cup measures 132 mm x 54 mm across the top face and 48 mm in height, so it drops into the same slot position as the cup it replaces. No adapter plate, no re-machining of the grid. It is one of 9 sizes in the same 132 mm family - 3 top widths (54 / 75 / 146 mm) by 3 heights (29 / 48 / 74 mm) - so a single order can cover every pod position on the machine.

Three things go wrong on a nesting table: a pod stops sealing, a panel lifts a fraction of a millimetre mid-cut, and the replacement cup arrives at the wrong height, so the grid gets re-levelled. The 132*54*48 vacuum suction cup targets that third failure - the 48 mm version of the 132 x 54 mm Biesse pod, not a 29 mm or 74 mm body on a shim.

One bakelite (plastic) cup, 132 x 54 mm across the top face, 48 mm tall, in grey. The top surface is precision-machined, so the seal line stays continuous around the perimeter, and a thermoset body holds that 132 x 54 mm section under vacuum instead of collapsing like soft rubber.

It belongs to a 9-size family: 3 top widths (54 / 75 / 146 mm) by 3 heights (29 / 48 / 74 mm). One order covers the small 54 mm pads, the long 146 mm pads and the deep 74 mm bodies, removing the mixed-height row where a 0.2 mm lift starts.

Fit is the point: it is listed as a spare for Biesse CNC machines, mounts on existing vacuum blocks without an adapter, and customization is supported for non-standard height or colour. Grey is standard, brown is produced, price is quoted per order, and shipping is by air, by sea or by express.

These are the numbers that decide whether the cup seats on your table.

• Top face matched to the grid - 132 x 54 mm contact area, the same slot pitch, so the table needs no re-drilling.
• 48 mm body, middle of three - 48 mm against 29 mm and 74 mm versions in the same footprint, so no shim is needed.
• Nine sizes, one family - 3 widths (54 / 75 / 146 mm) x 3 heights (29 / 48 / 74 mm) = 9 pods, one order covers a mixed table.
• Bakelite, not soft rubber - thermoset body keeps its 132 x 54 mm section under vacuum instead of closing up when the pump pulls.
• Machined sealing face - top rim machined flat, so the seal runs unbroken around the whole 132 x 54 mm perimeter.
• Grey standard, brown on request - 2 colours produced; a coloured pod stands out among worn ones on a grey table.
• Drop-in spare for Biesse - sized for Biesse CNC machines and machining centres, mounted on existing vacuum blocks with no adapter plate.
• Customization supported - non-standard height or colour produced to order, with the 132*54*48 mm version as the baseline.
• One cup, not a set - supplied as a single replacement pod, so a cracked cup costs one part, not a full table set.

The choice on a worn pod is usually between running it until a panel slips and buying a box of ten when you need two. Neither is a good trade - here is what changes.

• Buy the height you actually run. The 48 mm body is ordered on its own, so you stop shimming a 29 mm cup up to table height and stop cutting a 74 mm body down.
• One order covers the whole table. With 9 sizes in the 132 mm family, the 54 mm pads, the 146 mm long pads and the 74 mm deep bodies ship together, which removes the mixed-height row problem entirely.
• A sealing line that stays closed. A machined top face and a thermoset body keep the contact ring continuous around 132 x 54 mm, so vacuum is spent holding the panel, not leaking past a witness mark.
• Consumable logic, not capital logic. Pods wear out; a single replacement cup means the cost of a worn seat is one part, not a full set of nine.
• Colour as a maintenance cue. Grey is standard and brown is also produced, so a fresh pod stands out against a table of tired ones during a 1-minute walk-round inspection.
• Custom sizes without a new supplier. Because customization is supported, a non-standard height or colour comes from the same source as the standard 132*54*48 mm part.

Only if your table currently uses the 132*54*48 mm position. The cup is listed as a spare for Biesse CNC woodworking machines and machining centres, and it mounts on the existing vacuum block without an adapter plate - but the top face is fixed at 132 x 54 mm and the height at 48 mm, so check both against the pod you are pulling off.

132 x 54 mm at the top face and 48 mm high. Overall size is quoted as 132*54*48 mm, the SKU is 132*54*48, and the same 132 mm top width also comes in 75 mm and 146 mm versions at 29 mm, 48 mm and 74 mm heights.

It is bakelite, which is a thermoset plastic. That matters under vacuum: the body holds its 132 x 54 mm section instead of collapsing inward the way a soft rubber cup does when the pump pulls hard.

No. It is supplied as a single replacement pod, so a cracked cup is a one-part order. Replacing only the failed position also keeps the rest of the table at its existing, already-levelled height.

Yes. Customization is supported, so a non-standard height or colour can be produced to order. The standard baseline is the 48 mm grey version, and brown is also produced alongside grey.

Measure the top face and the height, in that order. The top face tells you the width group (54, 75 or 146 mm); the height tells you the body (29, 48 or 74 mm). Your two readings point at exactly one of the 9 combinations.

No. Grey is standard and brown is also produced, and both are the same bakelite part at 132 x 54 x 48 mm. Colour is a visual cue on the table, not a difference in the seal.

Price is quoted per order, so the figure depends on quantity and destination. Shipping runs by air, by sea or by express - the mode is chosen per order rather than fixed in the listing.