Cotton Cloth Buffing Wheel 180X50X20mm For Filato Nanxing Edge Bander

Need a replacement buffing wheel for a Filato or Nanxing edge bander without buying the whole polishing station? The BW015-1 is the wheel on its own: φ180 mm outside diameter, φ50 mm centre hole, 20 mm thick, cotton cloth around a steel core. It mounts on the buffing spindle and puts the gloss back on a trimmed edge. Three numbers decide the fit — 180 / 50 / 20 mm — and the 50 mm bore is the one that has to match first.

A buffing station fails in three ways that look the same on the finished panel. Wrong bore, so the wheel does not sit square on the spindle. A glazed face, so the edge leaves the trimming cut with a dull grey line under gloss banding. A size nobody wrote down, so the next order arrives a few millimetres out.

The BW015-1 answers all three: φ180 mm outside diameter, φ50 mm centre hole, 20 mm thick, cotton cloth on a steel core, for Filato and Nanxing edge banders. The diameter sets surface speed, the 20 mm face is the polish width, the 50 mm bore is the fit.

Cotton is the working part. The fibres carry compound and release it as the wheel turns, so the edge is polished rather than cut down. An abrasive changes the profile the trimming station set; cotton only levels the surface that cut left behind. Wear reads off the face, not the calendar.

Two numbers decide fit: the φ50 mm bore and the 20 mm thickness. Diameter is third. Other sizes and centre-hole shapes can be supplied, each wheel is packed in a carton box, and the match starts from the bore, diameter and width you measure off the old wheel.

What the three measurements and the cotton-over-steel build change at the buffing station:

• Cotton cloth face — the fibres hold compound and release it as the wheel turns, so the edge is levelled, not cut down.
• φ180 mm outside diameter — sets surface speed at the contact point, and has to suit the spindle speed the station runs.
• φ50 mm centre hole — decides whether the wheel mounts on the buffing spindle at all; check it before the diameter.
• 20 mm face width — the contact width along the edge, which fixes how much banding is polished in one pass.
• Steel core behind the cloth — the bore keeps its shape as the face wears back, instead of opening up off-centre.
• Cotton, not abrasive — polishes out the fine scratches the trimming cut left instead of grinding a new profile.
• Wear stays visible — compound and metal load the face until it glazes and goes hard, which is the point to replace.
• Filato / Nanxing fit — listed for these two edge bander families and mounted on the buffing spindle as a direct replacement.
• Other bores and sizes — alternative diameters, widths and centre-hole shapes when the measured wheel is not 180 x 50 x 20 mm.
• Carton box packing — one wheel per carton, so a replacement order does not need a pallet behind it.

What a correctly sized cotton wheel buys the shop that is currently making do:

• Re-ordering stops being a guess. Three numbers — 180, 50 and 20 mm — plus one SKU, BW015-1, so the second order matches the first without measuring the spindle.
• The grey line comes out. Trimming and scraping leave fine scratches; a cotton wheel loaded with compound polishes them out instead of leaving a dull line under gloss.
• Polish, not removal. The cloth levels the surface without cutting material off the banding, so the edge profile the trimming station set survives the pass.
• The bore survives the wear. A steel core holds the 50 mm hole round while the face wears back, so the wheel keeps running true.
• One wheel, one carton. Packed singly in a carton box, so replacing one worn wheel does not force a pallet order.
• Non-standard spindles are covered. Other diameters, widths and centre-hole shapes are supplied, so one odd machine does not need a second supplier.
• Made for the two machines it names. Filato and Nanxing edge banders take it on the buffing spindle as a direct replacement, with no adapter.
• Shipping follows the order size. Air, sea or express, so a station does not wait on a container when one wheel is missing.

Check the bore first — 50 mm. Then the thickness, 20 mm, then the 180 mm diameter. The bore is what decides whether the wheel mounts on the buffing spindle at all; the diameter can change without the wheel ceasing to fit.

The wheel only. BW015-1 is one cotton cloth buffing wheel, φ180 x φ50 x 20 mm, mounted on the buffing spindle of a Filato or Nanxing edge bander.

Because the edge has already been cut by the time it reaches the buffing station. Cotton holds compound and polishes the scratches out without grinding a new profile into the banding the way an abrasive would.

When the face glazes and the edge stops coming up glossy. The cloth loads with compound and metal pick-up, goes hard and shiny, and stops working long before the 180 mm diameter is worn down.

Yes, other centre-hole shapes and other sizes can be supplied. Send the bore, outside diameter and thickness you measure off the old wheel and the wheel is matched to those numbers.

The wheel is listed for Filato and Nanxing edge banders, and the fit is decided by the three measurements. Where 180 / 50 / 20 mm match, it mounts the same way on the buffing spindle.

Price is quoted on request — the listing carries no published figure. Wheels are packed in a carton box and shipped by air, by sea or by express, so a quotation covers the wheel and the freight method you pick.

The three measurements off the old wheel — bore, outside diameter and thickness — plus the machine model and the number of wheels. A photo helps where the bore is a non-standard shape.