Carbide Replacement Blade 15X13X2mm Scrapping Blades for Edgebanding Machine

Product Description

Need the insert that puts the radius back on a PVC or ABS edge without sending the blade out for regrinding? This is it: a 15 × 13 × 2 mm solid carbide profile knife for edgebanding machines, model EB009, SKU EB009-15X13X2. It seats in the profile-knife pocket, scrapes the surplus band and glue flash off the panel, and runs on PVC, ABS, acrylic and other banding materials — no sharpening step, no regrind queue. Custom profiles supported. Price on request.

An edgebanding cell that stops for a dull trimmer loses more than the blade: the radius goes rough, the glue line shows through the finish, and the operator picks up sandpaper to hide both by hand. Every replacement insert out of a different box cuts a slightly different panel. The EB009-15X13X2 takes all three off the line — a 15 × 13 × 2 mm carbide blade that drops into the profile-knife station and puts the edge back to spec on the next board.

It is a profile knife for an edgebanding machine, not a saw blade. It shaves away what the trimming cutters leave behind — the proud band on PVC, the rolled radius on ABS, the soft edge on acrylic — and refines the curved profile on furniture panels and cabinet parts. The edge is ground into a solid tungsten carbide body, not brazed onto a steel strip, so the 15 mm length and 13 mm width stay straight and the 2 mm thickness holds its seat under load.

Fitting takes minutes: the insert locates in the existing pocket, the clamp closes, and it runs stable from the first panel. There is no sharpening step on your side. A dull edge is swapped for a new insert, so the geometry after every change matches the day the machine was set: same radius, same clamp height.

Product Features

What makes the EB009-15X13X2 a fit for a production edgebander, not a generic trimmer:

• Solid carbide body — the edge is ground into a 15 × 13 × 2 mm tungsten carbide block, not brazed onto steel, so the 2 mm seat cannot delaminate mid-run.
• Radius trimming profile — the ground profile follows the panel radius instead of chipping the corner, which leaves a smooth, paint-ready edge on PVC and ABS.
• Scraper action on the glue line — it shaves the surplus band and the squeeze-out the trimming cutters leave, so the panel skips the hand-sanding step.
• 15 × 13 × 2 mm pocket fit — the 2 mm thickness is what the clamp expects, so the insert sits flat instead of rocking.
• Four materials, one part number — PVC, ABS, acrylic and other banding materials run on the same insert, so the crib holds one SKU.
• Wear resistance — carbide keeps a cutting edge through continuous production, so a dull blade is swapped, not reground mid-batch.
• Repeatable setting — replaced, not ground back, so the clamp height does not creep and the radius repeats insert after insert.
• Drop-in installation — clean the pocket, seat the insert, close the clamp; no shimming.
• Customisation supported — a non-standard radius is quoted to your drawing, so one machine model does not lock you to one parts list.

Product Parameters

Product Advantages

The choice usually runs between sending panels back for hand scraping and paying dealer price for whatever insert the machine maker has on the shelf. The EB009-15X13X2 is the third option: a 15 × 13 × 2 mm carbide insert you hold in your own stock.

• The edge stops depending on who is on shift. A new insert is a known quantity — same radius, same 2 mm seat — so the finish no longer drifts while somebody hones an old blade by hand.
• Hand sanding comes off the job card. The scraper action takes the surplus band and glue flash in one pass, removing a manual step from every PVC or ABS panel.
• One SKU covers four materials. PVC, ABS, acrylic and other banding run on the same insert, so the crib holds one part number instead of one per material.
• No regrinding loop. Nothing leaves the plant and nothing comes back with a geometry that no longer matches the pocket.
• Cost that tracks output. A 15 × 13 × 2 mm solid carbide edge is a consumable you schedule, not a failure you discover the day the trimmer starts tearing the band.
• A custom radius does not force a new supplier. Customisation is supported, so a non-standard profile is quoted from your drawing.

Frequently Asked Questions

Which machines do these 15 × 13 × 2 mm blades fit?

Edgebanding machines — this is the profile knife insert, not a saw blade. The EB009-15X13X2 body seats in the profile-knife pocket, where it does the radius trimming and scraping pass after the trimming cutters. Check your pocket against the 15 × 13 × 2 mm body before ordering.

Are these radius trimming knives or scraping blades?

Both — it is one part described two ways. The same EB009 carbide insert trims the radius and scrapes the surplus band, so you do not need two part numbers or two setups.

Which edge banding materials can I run with them?

PVC, ABS, acrylic and other edge banding materials. One carbide insert covers the range because the wear resistance sits in the material, not in a coating that rubs off.

Why carbide instead of a steel trimming blade?

Carbide holds the cutting edge through continuous production, so the blade is replaced rather than re-honed. A steel strip loses its ground geometry as it is sharpened back, and that is the drift you feel as a radius that stops matching.

How do I fit a new insert?

Clean the pocket, drop the insert in, close the clamp — no shimming. The 2 mm body is what the clamp is set for, so the blade is stable in operation from the first board.

Will the second insert cut the same as the first?

Yes, and that is the reason to replace rather than regrind. Each insert carries the original ground 15 × 13 × 2 mm geometry, so the radius does not creep when a blade is changed mid-production.

Can I get a different size or radius?

Yes — customisation is supported. Send the pocket dimensions and the radius you need, and the insert is quoted to that profile instead of to a catalogue number.

How much does one insert cost?

Price is on request. Send the quantity, the machine you are running and the banding material, and the quote is built on that mix rather than on a single list price.