Narrow Panel Feeding Device Manual Folding Feeder Edge Banding Machine Part

Need to keep a narrow strip against the fence while the edge banding machine pulls it through? This folding feeder does exactly that one job. It bolts to the infeed side, folds down to press a narrow panel onto the fence and folds up to clear a full-width board. Iron panel body, PU wheels, electro galvanized, manual folding with a pneumatic version also available. One carton at 56 × 23 × 14 cm, 9 kg gross, shipped from Mainland China.

Every shop that bands narrow strips hits the same three things: the strip wanders off the fence mid-pass, someone stands at the infeed holding it by hand, and the glue line comes out wavy enough that the strip has to be pulled off and run again. The Narrow Panel Feeding Device is built to remove all three.

It is a folding feeder that fixes to the infeed side of an edge banding machine and presses a narrow board down and against the fence, so the strip cannot walk. The body is iron panel, the parts touching the workpiece are PU wheels, and the unit is electro galvanized — a finish that survives glue, moisture and swarf sitting on the machine all day.

The arm is manual folding: swing it down for a narrow strip, fold it up out of the way when a full-width panel comes through, with no tools between the two. A pneumatic version of the same feeder is also available if your line prefers an air-driven arm to a hand-folded one.

Each unit ships as one carton measuring 56 × 23 × 14 cm at 9 kg gross, from Mainland China. It is classed as a woodworking machinery tool and sold as an edge banding machine spare, so it adds to the machine you already run.

What you get on the machine, in the order an operator notices it:

• Stops the strip running off — the feeder presses the narrow board onto the fence for the whole pass, which is the entire job of the part: no drift, no second run.
• Manual folding arm — fold it down for narrow strips, fold it up for full panels; one movement, no tools, no air line to connect.
• Pneumatic variant on request — same feeder body with an air-driven arm, for lines that would rather not fold it by hand.
• Iron panel body — the frame is iron panel rather than a thin folded bracket, so the arm keeps its line pass after pass.
• PU wheels at the contact — the strip runs on PU wheels, so the guide is a rolling contact instead of a steel edge the board slides against.
• Electro galvanized finish — electro galvanized throughout, which matters where glue, coolant and humidity sit on the machine between shifts.
• Fits existing machines — supplied as an edge banding machine spare, so it mounts at the infeed side of the machine already on your floor.
• One carton, 9 kg — 56 × 23 × 14 cm packed and 9 kg gross, small enough to move by courier when a line is standing.

Most shops handling narrow strips have two options: hold the strip by hand, or stop banding it and buy the strip pre-glued. This feeder is the third option.

• No second pair of hands. One operator can load, band and stack, because the feeder holds the strip against the fence while the machine's chain pulls the board through.
• Fewer re-runs. When the strip does not drift, the glue line stays parallel to the edge, so panels come off the outfeed ready to trim instead of going back around the machine.
• Fits the machine you own. It is an iron panel and PU accessory sold as an edge banding machine spare — a bolt-on addition, not a new machine and not a new routine.
• Low upkeep cost. Two material groups only, galvanized iron and PU wheels, so the wear item is a small wheel rather than a complete feeder assembly.
• Short downtime. 9 kg in a 56 × 23 × 14 cm carton arrives as one parcel, so a stopped line is not waiting on a pallet.
• No air to plumb. The standard manual version works on a machine that has no spare air outlet, which is usually the case on older edge banders.
• Factory direct. Bought direct from the maker in Mainland China, so a replacement is a spare-part order and not a machine order.

It stops a narrow strip from drifting off the fence while it is being banded. The feeder presses the board down and against the fence at the infeed, so the strip enters the banding station square — the failure it removes is the crooked glue line that forces a second pass.

It fits as a bolt-on spare, so the answer depends on the mounting points at your infeed side, not on the machine brand. It is an iron panel feeder with PU wheels, 9 kg gross, and it is offered either manual folding or pneumatic — send a photo of your infeed area and the machine model and the fit can be confirmed before you order.

No. The standard unit is manual folding, and the pneumatic version is an option on the same feeder. If your shop has no spare air outlet at the infeed, the manual version installs without touching the air system.

Iron panel body, PU wheels, electro galvanized finish. The galvanizing is the rust answer: the whole unit gets the zinc coating rather than a painted shell over untreated steel, which is what keeps it usable in a shop with glue and moisture in the air.

One carton, 56 × 23 × 14 cm, 9 kg gross. That is the packed weight, so it includes the carton and any wrapping — the figure you need for courier quotes and for carrying it to the machine.

It is a part. The feeder has no drive of its own; it is a guide that fixes to the infeed side of the edge banding machine, and the machine's own feed chain moves the board through it.

The panel meets PU wheels, not bare steel. PU is the only contact material at the guide point, so the strip is not sliding against a metal edge — that is the reason the wheels are PU rather than steel rollers.

It bolts to the infeed side of the machine and the arm is set by hand. There is no wiring and no air line on the manual version, and the unit is 9 kg, so it can be held in place while the fixings are tightened.