Edgebander SCM Spare Parts Chain Pad Replacement 80x62mm CCE024

Replacing a glazed conveyor pad on an SCM edgebander? The CCE024 chain pad measures 80 × 62 mm — 80 mm long, 62 mm wide — and takes the worn pad's place on the same chain link, so the track needs no machining. It is plastic and rubber, with a rubber face where the panel rides, finished in gray so wear shows. Listed for SCM edge banding machines; OEM production available. Measure one existing pad with a caliper, then order the CCE024. Price on request.

A worn chain pad never fails loudly. The panel starts skating a few millimetres on the conveyor, the glue line drifts out of parallel with the board, and the machine sits idle while somebody walks the chain hunting the one block that has gone smooth. Three symptoms, one small part.

The CCE024 is that part. It is a conveyance chain pad for SCM edge banding machines, 80 mm long and 62 mm wide, an 80 × 62 mm footprint that takes the place of the worn original on the same chain link and puts an unworn gripping face back under the panel.

The pad is made from plastic and rubber: a plastic block that keeps its shape on the link, with a rubber contact face where the panel rides. That rubber face is what limits slip while the board is carried through gluing, trimming and polishing. The finish is gray, so a glazed pad is visible at a glance against the chain.

It is listed as a replacement pad for SCM edge banding machines, and OEM production is available for buyers who need their own marking. Price on request. Order by model number CCE024; if your pads measure something other than 80 × 62 mm, check the other chain pad sizes.

Eight facts about this pad, and the first one is the one that decides whether it fits:

• 80 × 62 mm footprint — 80 mm long and 62 mm wide, the size the link is already cut for, so the track needs no machining and no re-pitching.
• Two-material construction — a plastic body carries the load while a rubber layer on the contact face does the gripping, so the wear surface does the work.
• Rubber contact face — the panel rides on rubber, not bare plastic, which is what limits slip between board and conveyor.
• Gray finish — supplied in gray, so a flattened face reads immediately on a walk-round instead of hiding against the chain.
• Replacement, not modification — one 80 × 62 mm pad comes out, one goes in, using the chain position the machine was set up on.
• Listed for SCM edge banders — specified for SCM edge banding machines, where the conveyance chain carries the panel past gluing, trimming and polishing.
• OEM available — made to order, so a buyer with their own part numbering can take the pad in their own marking.
• Ordered by CCE024 — the model number on the pad is the one you quote, which keeps an 80 × 62 mm pad from being swapped with a look-alike.

Maintenance planners usually get two bad choices: run the pad until edge quality falls off the line, or stop the machine and wait for a part. A correctly sized pad on the shelf removes most of that wait.

• The line comes back without a re-setup. Swapping one 80 × 62 mm pad leaves the chain where it was, so the datum the machine was aligned on is still the datum.
• Edge quality stops drifting. A rubber face that still grips holds the board square to the glue station, which is the difference between a trimmed edge and a re-work pile.
• Downtime measured in pads, not days. An 80 × 62 mm block is a shelf item, so a worn position is renewed from stores instead of waiting on a delivery.
• Sized by a caliper, not by the machine's build year. The 80 mm × 62 mm dimension is what matches the link, so the check before ordering is a measurement rather than a manual lookup.
• One part number to quote. CCE024 survives shift changes and store transfers, so reordering does not depend on who wrote the requisition.
• Own marking for repeat buyers. OEM production lets a buyer who labels their own spares take the 80 × 62 mm pad in their own marking.

Yes, if the pads on your chain measure 80 × 62 mm. The CCE024 is 80 mm long and 62 mm wide, so it sits in the same link position; measure one existing pad with a caliper before ordering.

80 mm long, 62 mm wide, an 80 × 62 mm footprint. Both figures are in the parameter table above, so the chain link can be measured against them directly.

Plastic and rubber. The body is a plastic block that holds its shape on the chain link, and the face the panel rides on is rubber.

Only the pad. CCE024 is a replacement conveyance chain pad; the chain itself and the surrounding components are separate items.

Count the pads on your chain. There is no fixed number per machine — order one CCE024 for each 80 × 62 mm position you want to renew, and keep a spare pair on the shelf.

Yes. OEM production is available, so the pad can be made to order for buyers who use their own part numbering or branding.

Yes. Other chain pads, press wheels and edge banding machine spares are available, so measure the link and ask for the matching size instead of forcing an 80 × 62 mm pad.

Send the model number and the quantity. CCE024 is quoted on request, so the fastest route is the model number plus the number of pads you need.