Edgebander Chain Pad 70x37xH37.5 for SCM 29L0184850H Edgebanding Machine Spare Parts

Need the exact chain pad for an SCM edgebander and not another near-size block? 29L0184850H measures 70 mm long, 37 mm wide and H37.5 mm high, with a grey rubber grip face on a black plastic base. It rides the conveyor system under the panel, so a worn pad shows up as creeping boards and off-parallel trim. Part number plus three published dimensions, so the pad in your hand can be measured against the one on the way, and the pad is listed for SCM machines that run this part number, quoted per order.

A chain pad that has gone flat shows up three ways: panels creep sideways on the conveyor, the trim comes out a fraction off-parallel, and the edgebander stands idle while a small rubber block is sourced from overseas. It is the cheapest part on the track and the one that decides whether the board reaches the trimming unit square.

29L0184850H is the replacement edgebander chain pad for SCM edgebanding machines, the block that rides the conveyor chain and carries the panel past the gluing station and the trimming units. Dimensions are 70 mm long, 37 mm wide and H37.5 mm high, so both the footprint and the stack height line up with the original position on the track.

The body is rubber plus plastic: a grey rubber grip face on a black plastic base. The rubber takes the friction, the plastic base holds the mounting height, so the pad does not squash under load and panel level stays constant along the track.

Because the grip face and the height are what wear, the pad is a consumable that is simply swapped, with no machining, no shimming and no track adjustment. This one is matched to part number 29L0184850H and listed for SCM edgebanders, so the number on the machine is what the order gets checked against.

Four things decide whether a chain pad works on an SCM track.

• Part number, not a lookalike — 29L0184850H is the reference, so the order is matched to the number on the machine, not to a photo of a similar block.
• Published in three axes — 70 mm long, 37 mm wide and H37.5 mm high, so the worn pad can be measured against the new one on the bench.
• Made for the SCM track — Listed for SCM edgebanders, the conveyor system that moves panels through gluing, pressing and trimming.
• Rubber where it grips — The grey rubber face sits against the panel and takes the friction, so the board is driven along the track instead of being dragged.
• Plastic where it mounts — The black plastic base carries the 37.5 mm height under load, so the panel level does not drop from one station to the next.
• Height, not just footprint — A pad with the right length and width but the wrong height tilts the panel at the trimming unit.
• A wear part you can plan — Rubber wears with running hours, so a spare on the shelf turns a stopped line into a five-minute swap.
• Three checks without tools — Grey face, black base, 70 x 37 mm footprint: the pad can be identified from the operator side of the machine.

The choice on a worn chain pad is usually between two bad options: keep running a pad that no longer grips, or stop the edgebander over one small block.

• A swap, not a shutdown. A worn pad takes a whole edgebander offline, and 29L0184850H on the shelf turns that breakdown into one part changed on the track.
• The same part twice. 29L0184850H on the order and 29L0184850H on the box, so there is no second-guessing whether the block that arrived is the shape the track needs.
• Trim stays parallel. Grip across the full 37 mm width keeps the panel from creeping between the glue station and the trimming units.
• Height held under load. The plastic base keeps the 37.5 mm stack height, so the top and bottom trim stay even instead of drifting apart along the line.
• A drawing is enough. Three published dimensions plus the part number give a fitter everything needed to confirm the pad before it ships.
• Grey rubber, black base. The two materials are visible from the operator side, so a worn face is spotted during a normal walk-round.
• A consumable, priced as one. The pad is quoted per order against the quantity needed, so a single spare and a restock are both quoted on the same part number.

SCM edgebanding machines. 29L0184850H is the edgebander chain pad for the conveyor track on an SCM edgebander, and it is ordered by part number plus the three published dimensions rather than by a photograph.

70 mm long, 37 mm wide and H37.5 mm high. Length runs along the chain direction, width across it, and the 37.5 mm is the height that sets panel level on the track.

Because height sets the level the panel rides at. A pad with the right 70 x 37 mm footprint but a shorter stack drops the board slightly, which shows up as uneven trim top to bottom.

Both. The grip face is grey rubber and the base is black plastic: rubber takes the friction and the compression, the plastic base holds the mounting height.

Read the number off the machine and measure the old pad. 29L0184850H plus 70 x 37 x H37.5 mm is enough to match the block; a photo of the worn pad beside a rule settles any doubt on an older build.

A straight swap. The pad is one block at its own position on the chain, so it is removed and replaced at the same 37.5 mm height with no shimming and no track adjustment.

Yes. Chain pads in other footprints, press wheels, suction gaskets and other edge banding machine spares come from the same catalogue, so a rebuild can be ordered as one shipment.

Quoted per order. The pad is priced against the quantity you need, so the figure comes with the quote for 29L0184850H rather than as a fixed number on this page.