SCM Edge Bander Buffing Wheels 160x50x20mm Wood Polishing Sanding Wheel

Putting a buffing station back into service on an SCM edgebander needs three numbers, not a machine survey: 160 mm outside diameter, 50 mm bore, 20 mm thickness, with a cloth working face. Those three dimensions are the whole fit check. The cloth holds the polishing compound and wipes residual glue and trim marks off PVC, ABS, melamine and veneer edges. Order by size, 160 × 50 × 20 mm; other sizes are quoted on request.

A buffing wheel does not fail with an alarm. It glazes over, stops holding compound and starts smearing the glue line instead of polishing it. The bore wears, the wheel runs out of true and chatters along the edge. The spare that finally arrives is the wrong thickness, so it marks the panel face it was meant to finish. Three failures, one part.

This is the cloth polishing wheel for the buffing station of an SCM edgebanding machine, the operation after end trimming and radius scraping. It measures 160 mm outside diameter, 50 mm bore and 20 mm thickness, and the working face is cloth. Cloth holds polishing compound on the face and wipes the edge; an abrasive disc would cut into it instead.

The three numbers are the fit check. 160 mm outside diameter reaches the trimmed edge across the panel thickness. A 50 mm bore seats on the buffing spindle as a straight swap, with no bushing or adapter. 20 mm of face width covers the glue line and stops short of the panel surface beside it.

Application is SCM edgebanding machine spare parts, on PVC, ABS, melamine and wood veneer edges. Ordering is by size: 160 × 50 × 20 mm. Other sizes are quoted on request, so a second machine on the line does not mean a second supplier.

What decides whether this wheel works is the three dimensions and the cloth face:

• 160 mm outside diameter — reaches the trimmed edge across the panel thickness, so the buffing station finishes the edge the trimming station cut.
• 50 mm bore — seats on the buffing spindle as a straight swap, so fitting is one tool change, not a machining job.
• 20 mm face width — works the glue line across 20 mm and stays clear of the panel face, so buffing does not mark the surface.
• Cloth working face — holds compound at the contact point and wipes residual glue and trim marks off the edge instead of removing material.
• Edge banding duty — specified for PVC, ABS, melamine and wood veneer, the four materials an SCM line runs.
• SCM spare-parts fit — listed as an SCM edgebanding machine spare, so the size is quoted against the machine, not a generic disc.
• Polishing station part — runs after end trimming and radius scraping, before the panel is packed.
• Simple upkeep — a soft brush or air blower clears compound and debris from the cloth face.
• Other sizes on request — a non-standard diameter, bore or thickness is quoted from your drawing or sample.
• One size reference — 160 × 50 × 20 mm identifies the part, so a reorder does not depend on the name.

At the buffing station the choice is usually a generic cloth disc that runs out of true, or waiting on a service visit for a part that takes one tool change to fit.

• The buffing station stops being the stoppage. A glazed wheel halts an SCM line as surely as a blunt cutter, so one spare at 160 mm on the shelf keeps the line working.
• A tool change, not a fitting job. The 50 mm bore matches the spindle the old wheel came off, so fitting takes one change and no adapter.
• No marks on the panel face. 20 mm of face width covers the glue line and stops short of the surface, which removes a re-work step at final inspection.
• The same finish on every shift. Re-ordering the same 160 × 50 × 20 mm specification keeps the edge consistent when the operator changes.
• One order covers a second machine. Sizes that are not on the list are quoted on request, so a mixed line is re-stocked from one purchase order.
• Compound stays at the contact point. The cloth face holds the compound on the working face instead of throwing it off the 160 mm rim.
• Reorders stop depending on description. Quoting 160 × 50 × 20 mm removes the ambiguity between buffing wheels that look the same on a shelf.

Yes, if your buffing station runs a 160 × 50 × 20 mm wheel. The 160 mm diameter, 50 mm bore and 20 mm thickness match the SCM buffing spindle; send the machine model with the order and the size is confirmed against it.

Outer diameter, bore and thickness. The wheel measures 160 mm across the outside, 50 mm through the centre hole and 20 mm on the face, which is the order edgebander buffing wheels are quoted in.

Cloth. That is why it polishes the glue line after trimming and wipes residual glue and trim marks off the edge instead of cutting material away the way a coated abrasive would.

PVC, ABS, melamine and wood veneer. One cloth wheel covers all four, so the buffing station does not need a different wheel per material.

Yes. Other sizes are quoted on request, so a different diameter, bore or thickness is answered from your drawing or sample instead of refused.

Clean it with a soft brush or an air blower. Clearing compound and debris from the cloth face is the whole maintenance routine for this part.

No. The cloth construction covers PVC, ABS, melamine and veneer on the same 160 × 50 × 20 mm wheel, so one spare serves the whole buffing station.

The size 160 × 50 × 20 mm plus the quantity. Price is quoted on request against that, because buffing wheels are also built to other sizes.