0333716046A Edgebander Parts Chain Pad Conveyor Pad for SCM Olimpic Edgebanding Machine 63x37mm Conveyance Track Pad

Product Description

Replacing a worn chain pad on an SCM edge bander? The CCE011 is a 63 x 37 x 15 mm conveyor pad in PA + rubber for SCM edge banding machines, listed under part number 0333716046A. Three numbers settle the fit: 63 mm long, 37 mm wide, 15 mm thick. The pad carries the panel along the conveyance chain, so a worn face shows up as an edge that no longer runs true. Price is quoted against the quantity per chain.

A conveyor pad wears quietly. The panel starts riding low on the chain, the trimmed edge comes out slightly off square, and the operator slows the feed to hide it. Pads on one chain wear to the same depth, so one new pad rarely cures the symptom.

The CCE011 is that pad: a chain pad and conveyor pad for SCM edge banding machines, sized 63 x 37 x 15 mm and made of PA + rubber. It sits on the conveyance chain and carries the panel through the machine. The PA body holds the shape where the pad locates, and the rubber face is the surface the panel rides on.

The three dimensions are the whole fit check: 63 mm long, 37 mm wide, 15 mm thick, measured on the pad you are replacing. A pad that matches in length and width but not in thickness still seats on the chain link, then sits proud or sits low, and the panel stops running flat. Measure thickness with the pad off the chain.

The rubber face is listed for heat resistance and wear, which is what a pad on a running chain meets: a warm panel and continuous sliding contact. Custom mechanical accessories can be supplied to a buyer's requirement, so a non-standard pad is quoted rather than refused. Price is on request, against the quantity per chain.

Product Features

What the part number fixes, and what to measure on the machine before ordering:

• SCM edge bander fit — a conveyor pad for SCM edge banding machines, ordered by part number CCE011 / 0333716046A instead of being cut to size on site.
• 63 x 37 x 15 mm — length, width and thickness of the pad footprint, all three read off the worn pad.
• PA + rubber — a PA body for the structural seat on the chain link, a rubber face where the panel makes contact.
• Heat resistance at the contact face — the rubber is specified to hold against a warm panel and continuous sliding contact.
• Wear resistance — the rubber face is the layer that gives up material, so the PA body below keeps its dimensions.
• Same position, no machining — the pad goes back where the worn one came from, so chain tension stays as it was set.
• Consumable, not a rebuild — pads come off and go on as single items, so a worn chain is restored by swapping parts.
• Custom accessories on request — mechanical accessories can be produced to a buyer's own requirement when the standard size does not match.

Product Parameters

Product Advantages

A pad is the cheapest part on the chain and the most expensive one to get wrong, because the cost lands on the edge rather than on the parts invoice:

• A flat face keeps the edge square. A pad worn hollow lets the panel rock over the trim station, and a rocking panel loses more from one end of the edge than from the other.
• Buy the number, not a guess. 63 mm, 37 mm and 15 mm are read off the pad being replaced, so the part arrives usable instead of becoming shelf stock.
• Replace the set in one stop. Pads on one chain wear together, so one order for the whole chain avoids three or four separate stoppages.
• Nothing drilled or shimmed. The pad locates in the existing position on the conveyance chain, so no adaptor is needed to make it fit.
• One item sets the service interval. The rubber face wears and the PA body under it holds the fit, so the replacement decision belongs to a single part.
• Quotation against your machine. Send the machine model, the size off the old pad and the quantity per chain, and the price comes back matched to the SCM edge bander on your floor.

Frequently Asked Questions

Will the CCE011 fit my SCM edge bander?

Only if the size matches. The pad is 63 x 37 x 15 mm, so measure the pad you are replacing across all three and compare before ordering. Send the machine model with those numbers if you want the fit confirmed first.

What size pad do I need?

63 mm long, 37 mm wide and 15 mm thick, if your machine takes the CCE011. Those are the three figures taken off the worn pad; if any one of them is different, this part is not the one.

Is a conveyor pad the same as a chain pad?

Yes. This item is sold as a conveyor pad and bought as a chain pad for SCM edge banders; it is the same part that carries the panel along the conveyance chain.

What is the pad made of?

PA plus rubber. The PA body holds the shape where it seats on the chain link, and the rubber face is the surface the panel rides on.

Why does thickness matter as much as length and width?

Because the pad seats on the chain link and its top face sets panel height. A pad that is right in length and width but wrong in thickness still fits the link, then holds the panel proud or low.

How many pads should I order?

Count the pads on your chain, not the stations on the machine. Pads wear as a set, so most buyers order the whole chain at once rather than one pad at a time.

Can you make a non-standard size?

Yes, machinery accessories can be made to your requirement. Send the drawing or the dimensions you need and the quantity, and the custom part is quoted as a separate item.

How do I get a price?

Price is quoted on request, because a chain-set quantity prices differently from a single pad. Send model CCE011 or part number 0333716046A with the quantity per chain.