0390320645C SCM Spare Parts Morbidelli 145x55mm Upper Rubber Lip Gasket

Need the upper lip gasket for an SCM Morbidelli vacuum block? The 0390320645C is the 145 × 55 mm grey rubber seal that sits on the top face of the pod and presses against the panel, so vacuum holds instead of bleeding at the edge. Order by the part number and the 145 × 55 mm size; it is a wear part, so one spare per machine keeps the block off the waiting list. Supplied by Shunhongyu, packed in cartons, origin China.

Three things go wrong in a nesting cell when a vacuum block stops holding: the lip flattens, the lip tears at one corner, and the replacement gasket that finally arrives is the wrong size. Any one of them stops the machine. The panel creeps under the cutter, the operator re-seats the sheet by hand, and the scrap bin fills while someone hunts a spare. Changing the whole pod to cure a worn rubber lip is the expensive answer; the 0390320645C is the cheap one.

This is the upper rubber lip gasket for SCM Morbidelli vacuum blocks — the grey rubber seal that sits on the top face of the pod and presses against the workpiece. It is listed at 145 × 55 mm, the figure you take off the old gasket before ordering, and it is moulded in rubber, so the contact edge stays a defined lip instead of a flat pad. Under vacuum that lip closes the gap between block and panel, which is the whole job of the part.

Because it is a wear item, treat it as one: one spare per machine on the shelf, changed at the first sign of a flattened or nicked edge rather than the first ruined panel. Supplied by Shunhongyu, carton packed, origin China. The same range also covers vacuum cup gaskets for Homag, Biesse and other machines.

The part is small, so the specification is the whole story:

• Part number first — 0390320645C identifies the upper rubber lip gasket in the SCM Morbidelli range, so a re-order is a number match rather than a photo match.
• 145 × 55 mm footprint — measure the old lip end to end and edge to edge; the replacement is cut to the same two figures.
• Moulded rubber lip — rubber in grey, moulded as a lip, so the sealing edge stays distinct across the full 145 mm length.
• Top face position — it sits between the block and the panel, the first place a leak opens on a vacuum pod.
• Hand fit, no fixtures — one gasket lifts off and the new one seats on the same face: no press, no jig, no trimming.
• Woodworking accessory — listed as a woodworking machinery accessory for SCM Morbidelli vacuum blocks, with the block, hoses and fittings left in service.
• Three brands, one line — the same catalogue carries vacuum cup gaskets for Homag, Biesse and other machines, so one order covers several pods.
• Carton packed — shipped in cartons out of China, with the 0390320645C number on the packing list for the stock check at goods-in.
• Quoted per order — price is confirmed on the quotation, so the figure matches the quantity and packing you asked for.

When a block stops holding there are usually two options on the table: keep running a leaking pod and sand the marks out later, or buy a new pod and wait for delivery. A 145 × 55 mm gasket in the spares cupboard is the third.

• Replace the seal, not the pod. One 0390320645C gasket renews the contact face, while the block body, the vacuum line and the nesting program stay exactly as they were.
• One number, one size, no second order. The part number plus the 145 × 55 mm footprint is everything needed to match a worn gasket, so the parcel that arrives is the one you asked for.
• Vacuum stays at the pod face. A lip sealing across the full 145 × 55 mm footprint holds the panel at the edge, where a flattened lip loses it first.
• A wear part with a known job. The rubber lip is the first thing to flatten on a vacuum block, so one spare per machine turns a stopped spindle into a few minutes of work.
• Three brands from one carton. SCM Morbidelli blocks now, Homag and Biesse vacuum cups next, from the same carton-packing line in China.
• Priced against your order. Quotation-based pricing means the figure you sign off matches the quantity and packing you actually need, not a listed pack size.

Yes, if your block carries the 0390320645C part number and a 145 × 55 mm upper face. Match those two figures against the old gasket before ordering; a block built for a different lip size will not seal with this one.

It is the overall footprint: 145 mm long and 55 mm wide. Measure your worn gasket the same way, full length and full width, so the two sets of figures line up.

Rubber, moulded in grey. The seal is a single rubber part, so the lip bends against the panel and comes back when the vacuum is released.

A worn or nicked lip is the usual cause. Check the 145 × 55 mm sealing edge for a flat spot or a tear; once the edge has gone, a new 0390320645C gasket restores the seal without touching the block itself.

No. The gasket lifts off the top face of the block and the new one seats in its place by hand, so one block is a few minutes of work.

Yes. The same line carries vacuum cup gaskets for Homag, Biesse and other woodworking machines, so one order can cover more than one brand on the floor.

Carton packed, origin China. Gaskets travel boxed in cartons under the 0390320645C number, which makes the goods-in check a number match.

Price is quoted per order, not fixed on the page. Send the part number 0390320645C, the quantity you want and the destination, and the quotation comes back with price and packing confirmed.