65x8x14mm Rubber Pressure Roller Press Wheel for SCM Edge Banding Machine

A worn pressure wheel on an SCM edge bander shows up as a wavy glue line long before anything else fails. The PSW038 is Φ65 mm outside diameter, Φ8 mm bore, 14 mm face width, moulded in grey rubber with a smooth running surface, and it is built as woodworking machinery spares for SCM edge banding machines. Three measurements settle fitment: 65, 8 and 14. A gear roller of the same size is also available, in straight tracking and angle tracking patterns.

An edge bander that leaves a wavy glue line, a band edge that never sits flush, or a shadow under the tape usually has one worn part rather than a worn machine: the pressure roller. Three things make that repair annoying. The wheel costs less than the paperwork around it, the factory part search takes longer than the swap, and a wheel chosen by eye presses a different footprint onto every panel.

The PSW038 is a rubber pressure roller press wheel for SCM edge banding machines. Outside diameter is Φ65 mm, bore is Φ8 mm, face width is 14 mm — the numbers that decide whether a wheel lands on your existing axle. The body is grey rubber, the surface smooth, so pressure is carried across the full 14 mm face rather than a narrow ring.

Smooth is the version for bands that must not be marked. A gear roller bites into the band for grip; a smooth rubber roller presses it flat, which is what veneer, PVC, melamine and ABS need on a straight-line pressure station.

Because the wheel is specified by dimension, not machine model, it cross-references against any SCM edge bander station running a 65 mm outer, 8 mm bore, 14 mm wide wheel. A gear roller of the same size is also available, in straight tracking and angle tracking patterns.

What decides whether this wheel is the right one:

• Φ65 mm outside diameter. The running diameter that presses the band onto the panel edge — measure across the rubber face before ordering.
• Φ8 mm bore. A plain 8 mm centre bore, so the wheel mounts on the axle the old one came off.
• 14 mm face width. Contact width: the number that decides whether a band is pressed across its full thickness or only along the top.
• Grey rubber body. Moulded rubber in grey, the same colour family as the SCM pressure wheels already on the machine.
• Smooth running surface. No gear teeth on the face, so the roller presses the band instead of stamping a pattern into it.
• Gear roller alternative. The same 65 × 8 × 14 mm size is also supplied as a gear roller for stations that need positive tracking.
• Two gear patterns. Gear rollers are offered in straight tracking and angle tracking types.
• Four band materials. Veneer, PVC, melamine and ABS — the smooth face suits all four.
• SCM fitment. Specified as woodworking machinery spares for edge banding machines, in the original 65 × 8 × 14 mm footprint.
• One part number. PSW038 covers diameter, bore and width together, so quoting and re-ordering use one string.

The usual choice is between waiting on a factory part order and fitting a wheel that is close enough and hoping. The PSW038 is meant to turn that into a measurement: 65, 8, 14.

• One part number per size. PSW038 is always Φ65 mm × Φ8 mm × 14 mm, so a quote, a comparison and a repeat order all describe the same wheel.
• Measured, not guessed. If the old wheel measures 65 mm across the rubber, 14 mm wide, with an 8 mm bore, fitment is settled before the order leaves the desk.
• Bore first. An Φ8 mm bore goes straight onto the axle the worn wheel came off — no bushing, no reaming, no extra machining time on the station.
• 14 mm of contact. A narrow wheel presses a line; a 14 mm face presses across the band, which is where veneer and PVC actually need the pressure.
• Smooth face, four tapes. Veneer, PVC, melamine and ABS all press without a tooth mark left to sand out afterwards.
• Two surfaces, one supplier. Smooth and gear versions in the same size, so a mixed machine is covered by one purchase order instead of two.

Yes, if the machine runs a Φ65 mm pressure wheel with a Φ8 mm bore and a 14 mm face. Those three measurements are the whole fitment test — the part number on the old wheel does not change the answer.

Φ65 mm outside diameter, Φ8 mm bore, 14 mm face width. Nothing else needs measuring before an order.

Smooth. PSW038 is the grey rubber wheel with a plain running surface and no gear teeth on the face.

Yes. The same 65 × 8 × 14 mm size is also available as a gear roller, and gear rollers are supplied in two patterns: straight tracking and angle tracking.

Veneer, PVC, melamine and ABS. A smooth rubber face carries pressure onto the band without cutting a pattern into it.

Measure the old wheel. 65 mm across the rubber, 8 mm bore, 14 mm face width. If any one of the three differs, it is a different wheel.

No. The wheel is specified one at a time, so the worn station can be replaced on its own using its Φ65 mm × Φ8 mm × 14 mm measurements.

Yes. Pressure wheels differ in size and shape between edgebander brands, and other diameters, gear patterns and countersink versions are available on request.