65x8x25mm Rubber Press Wheels Smooth Roller for SCM Edge Banding Machine

Replacing a worn pressure wheel on an edge bander? The PSW037 is a smooth rubber press wheel measuring Φ65 mm outside diameter, Φ8 mm bore and 25 mm face width, moulded in grey rubber with a plain contact face. It presses veneer, PVC, melamine and ABS bands onto the panel across the full 25 mm width, and it is listed for NANXING and SCM-family edge banding machines that use this bore and width. Gear-tooth rollers and other diameters, widths and bores come from the same range.

A dull, shiny line along the edge joint is usually blamed on glue. In most workshops it is one of three hardware faults: the pressure wheel has flat-spotted or gone hard, the replacement arrived with the wrong bore so the wheel runs out of true, or the only wheel on the shelf fits one brand of bander. The PSW037 is built for the third and prevents the first two.

It is a smooth rubber press wheel: Φ65 mm outside diameter, Φ8 mm bore, 25 mm face width, moulded in grey rubber with a plain, un-toothed face. The 25 mm face covers standard furniture band widths, and a plain face holds contact along the whole band rather than at discrete teeth, so no gear pattern is pressed into soft PVC or thin veneer.

The bore is a true Φ8 mm, concentric with the Φ65 mm rim, so the wheel seats on an 8 mm shaft without a shim or tape wrap. Because the rim stays at 65 mm, the arm keeps its height and a change is one bolt, not a re-alignment.

The wheel runs against veneer, PVC, melamine and ABS banding. Gear rollers, and the same wheel in other diameters, widths and bores, come from the same line in Foshan, Guangdong. For a shop with a bander down, that turns a part on order into a shelf part.

What separates this wheel from a generic rubber roller:

• Smooth contact face — a plain rubber face spreads load over the full 25 mm width instead of concentrating it on gear teeth.
• Φ65 mm outside diameter — the same rim height as the wheel it replaces, so the pressure arm does not need re-setting after fitting.
• Φ8 mm bore — one true 8 mm bore, concentric with the 65 mm rim, seats straight on an 8 mm shaft with no shim.
• 25 mm face width — 25 mm of contact across the band, the width used on standard furniture panel edges.
• Grey rubber body — moulded in grey, the colour of this part number, so a mixed shelf sorts by eye.
• Four band materials — veneer, PVC, melamine and ABS all run against the same 65 × 8 × 25 mm wheel.
• Gear roller available — a toothed version is supplied from the same range for machines that feed with a gear wheel.
• Other sizes on request — diameter, width and bore can be matched to a shaft, so one supplier covers a mixed machine park.
• One part number, one fit — PSW037 reorders as 65 × 8 × 25 mm, not as a near-size match.
• Dispatch from Foshan — the wheel leaves from Foshan, Guangdong, China, with the rest of the SCM spare-part range.

On a worn pressure wheel the usual choice is to wait for an original part, or to fit a near-size wheel and live with the wobble. The PSW037 takes both options off the table.

• No re-setting after a change. The rim stays at 65 mm, so the pressure arm keeps its height and the swap is one bolt rather than a re-alignment.
• No shimming on the shaft. A true Φ8 mm bore centres the wheel on the shaft, which is what stops the run-out that shows up as a wavy glue line.
• No tooth marks on soft edges. The plain face spreads pressure over 25 mm, so PVC and thin veneer are pressed, not indented by a gear pattern.
• One wheel, four band materials. Veneer, PVC, melamine and ABS share one part, so the shelf holds one SKU instead of four.
• A shelf part, not an order. Because 65 × 8 × 25 mm is a standing size, a worn wheel is replaced from stock instead of stopping the line for a delivery.
• Two banders, one matched height. Reordering PSW037 gives the same 65 mm rim, so two machines on the same head stay at the same pressure setting.
• A mixed machine park, one list. Gear rollers and other bores come from the same range, so a shop running NANXING alongside SCM machines orders once.

Yes, if the machine takes a Φ65 mm wheel with a Φ8 mm bore and a 25 mm face. The wheel is listed for NANXING edgebanders and for SCM edge banding machines on this bore and width, so measure the shaft and the old wheel before ordering: all three numbers have to match.

Smooth. PSW037 has a plain grey rubber face at 25 mm width. If your machine feeds with a toothed wheel, the gear roller version is available from the same range.

No. The outside diameter is Φ65 mm, the same as the part it replaces, so the pressure arm keeps its working height and only the mounting bolt is touched.

Veneer, PVC, melamine and ABS. The plain face presses across the full 25 mm width, so soft PVC and thin veneer take the pressure without a tooth pattern.

Usually yes, and it is the bore or the shaft. A bore that is not a true Φ8 mm lets the wheel run out of centre, so check bore and shaft for wear before fitting a new 65 mm wheel.

Yes. Other diameters, widths and bores are available on request, and gear rollers are supplied from the same range. Send the outside diameter, bore and face width you need and the match is confirmed against your shaft.

One spare for every pressure station in use. A rubber wheel is a wear part, and holding a 65 × 8 × 25 mm spare means a rounded edge is a ten-minute change, not a stop.

From Foshan, Guangdong, China. Quantity, price and delivery are confirmed on the quotation, because the same range is supplied in several sizes and two surface types, so the terms follow the actual mix on the order.