71x48mm Chain Pad for SCM Automatic Edge Banding Machine CCE007

Need the right conveyor pad for an SCM automatic edge bander? The CCE007 is a 71 x 48 mm replacement pad in PA + rubber, built to sit on the conveyance chain and carry the panel past the glue, pressure and trimming stations. Measure the worn pad across both axes, compare 71 mm and 48 mm, and the fit is settled before you order. Supplied bulk packed and disassembled, as the product photos show. Price on request; send the quantity per chain.

A worn conveyor pad rarely stops a line. What happens is quieter: panels ride unevenly on the chain, the edge banding sits a fraction off square, and the operator slows the feed to compensate. By the time the pad looks worn, the pads either side of it are worn to the same depth.

The CCE007 is the replacement conveyor pad for SCM automatic edge banding machines, at 71 x 48 mm. It sits on the conveyance chain and carries the panel past the glue, pressure and trimming stations, so the top face takes the sliding load while the body holds position on the chain link. Material is PA + rubber: a PA body for the structural fit, a rubber face where the panel actually rides.

Both numbers are the fit check. 71 mm and 48 mm describe the footprint you measure on the pad in your hand; a pad that is right on one axis and wrong on the other will still seat on the chain link but sit proud of the surface, and a proud pad is a panel that no longer runs flat.

The pad is supplied bulk packed and disassembled, as the product photos show, so a full-chain order travels compact. To order, send model CCE007, the two measurements off the worn pad, and the quantity per chain.

What the part number fixes, and what to check on the machine before ordering:

• SCM edge bander fit — specific to the conveyor pad position on SCM automatic edge banding machines, so it is ordered by part number rather than cut to size.
• 71 x 48 mm — two numbers, both measured off the worn pad; length and width are the whole fit check on this item.
• PA + rubber — a PA body that keeps its shape on the chain link, and a rubber face where the panel makes contact.
• Wear face where the load is — the rubber top takes the sliding contact, so the body below keeps its dimensions while the surface does the wearing.
• Same position, no machining — the pad replaces the worn item on the conveyance chain, so chain tension and track height stay as they were.
• Single central fixing — one screw through the middle of the body, as the product photos show, locates the pad on the chain link.
• Bulk packed, disassembled — supplied as pictured, which keeps a chain-set order compact in transit.
• Consumable, not a rebuild — pads come off and go back on as one item, so a worn chain is restored by swapping parts instead of stripping the track.

A pad swap is cheap; a pad swap done twice is not, and the cost shows up at the ends of the panel rather than on the parts invoice:

• A flat face keeps the edge square. A pad worn hollow lets the panel rock, and a rocking panel leaves the trim station cutting more from one end than the other, which is rework no sander will take out.
• Order the number, not a guess. 71 mm and 48 mm are measured on the pad you are replacing, so the part arrives usable instead of becoming shelf stock.
• Replace a set, lose one stop. Pads on one chain wear together, so a single bulk-packed order for the whole chain avoids three or four separate stoppages.
• No machine modification. The pad drops into the existing position on the chain, so nothing is drilled, shimmed or re-tensioned to make it fit.
• A wear part you can plan around. The rubber face is the layer that wears and the PA body underneath keeps the fit, so the replacement interval is set by one item.
• Quotation against your machine. Send the quantity per chain with the pad size and the quote covers the part that matches the SCM edge bander on your floor, delivered from Guangdong.

Only if the size matches. The pad is 71 x 48 mm, so measure the pad you are replacing across both axes and compare before ordering. Send the machine model with that measurement if you want the fit confirmed first.

They are the pad footprint, and both have to match. 71 mm and 48 mm are taken across the two axes of the pad; one that is right on one axis and wrong on the other seats on the chain link but sits proud.

Yes. This part is listed as a conveyor pad and bought as a chain pad for SCM edge banders; it is the same item that carries the panel along the conveyance chain.

PA plus rubber. The PA body holds the shape where it locates on the chain link, and the rubber face is the surface the panel rides on.

Count the pads on your chain, not the stations on the machine. Pads wear as a set, so most buyers order the whole chain set at once rather than one pad at a time.

Bulk packed and disassembled, as the product photos show. A chain-set order therefore travels as compact parts rather than assembled blocks.

No. The pad replaces the worn part in the same position on the conveyance chain: no machining, no adaptor, and chain tension is left as it is.

Price is quoted on request, because a chain-set quantity prices differently from a single pad. Send model CCE007 and the quantity per chain, and the quotation comes back with delivery from Guangdong Province, China.