122x61x15mm SCM Spare Parts Rubber Suction Plate for CNC Machine Vacuum Suction Spares

Product Description

What is a 122x61x15mm rubber suction plate? It is the gray rubber ring that seals a vacuum block on an SCM CNC machining centre. 122 mm outside diameter, 61 mm bore, 15 mm thick, moulded in rubber, supplied as a direct replacement for a worn plate. The ring beds into the block groove and holds the panel while the spindle cuts, so the plate is swapped instead of the whole block. Bulk packed in a standard export carton. OEM/ODM sizes available on request.

A vacuum block that lets go mid-cycle stops the spindle, spoils the panel and leaves the operator re-zeroing the nest. Most of the time the cause is the rubber ring on top of the block, not the block itself: the plate has hardened, the sealing face has taken a set, or the ring never matched the groove. The 122x61x15mm rubber suction plate is the replacement part for that failure.

It is a ring, not a flat pad. 122 mm outside diameter, 61 mm bore, 15 mm section thickness, moulded in gray rubber with a stepped face that beds into the machined groove of the vacuum block. The outer face carries the panel, the bore clears the vacuum port, and the stepped shoulder keeps the plate centred under load instead of creeping sideways.

Fitment goes by size and by block pattern, not by machine year. The plate is listed for SCM vacuum blocks and Morbidelli heads, and it is one of a family: square pads come in 130x30x17, 120x50x17, 125x75x17, 126x75x17, 145x115x17, 160x115x17 and 140x130x17 mm, with a φ109x54x18 mm ring for the smaller stations.

Plates ship packed in bulk in a standard export carton, sized to the quantity ordered, with a moisture-resistant outer box. OEM/ODM work is available, and video or online technical support covers fitting questions.

Product Features

What decides whether this ring seals on your block:

• 122 mm ring with a 61 mm bore — the three figures that matter when you match the plate to the groove: 122 mm outside, 61 mm bore, 15 mm thick.
• One-piece gray rubber moulding — no bonded joint across the sealing face, so there is nothing to split under vacuum.
• Stepped sealing face — the shoulder steps down to the bore, so the plate registers on the block instead of squashing out sideways.
• Sold as the ring only — the aluminium block, its valve insert and its locating ring stay on the machine.
• A family of pads, one order — eight square sizes from 120x50x17 mm to 160x115x17 mm, plus a φ109x54x18 mm ring, cover the other stations on the same table.
• Matched spares in the same carton — valve inserts, locating rings and gaskets can be added to the same shipment.
• SCM and Morbidelli fitment — the same range covers Homag, Weeke, IMA, Biesse Rover and Excitech heads.
• Bulk export carton — standard carton with a moisture-resistant, high-compression outer box, sized to the quantity ordered.
• OEM/ODM to drawing or sample — non-listed sizes are moulded to the drawing or the worn plate you send.
• Support after the carton — video and online technical support for fitting and size checking.

Product Parameters

Product Advantages

The choice is usually between waiting on an imported block and running on with a plate that leaks. A ring in stock removes both options from the list.

• A ring, not a block. You buy the wear item at 122x61x15mm and keep the block, its valve insert and its locating ring, instead of pulling a complete pod off the table.
• Downtime in minutes. One plate lifts off and one presses back on; the block face is not re-machined and the machine is back in the nest the same shift.
• Numbers a caliper can check. 122 mm outside, 61 mm bore, 15 mm thick — three figures to hold against the old plate before anything is ordered.
• Seal where the leak starts. The 15 mm rubber section and the stepped face close the gap between block and panel.
• Every station covered. Eight square sizes plus a φ109x54x18 mm ring mean one order serves the whole nest, not one pod.
• Freight paid on parts, not air. Bulk cartons are sized to your quantity, so a stock order arrives in one box.
• Size checked before you cut. Video and online support confirm the plate against your old one.

Frequently Asked Questions

Will this plate fit my SCM CNC machine?

Yes, if your vacuum block takes a 122 mm ring plate. Fitment goes by the block, not the machine year: measure the old plate across the outside at 122 mm and the bore at 61 mm, and the 15 mm section should sit in the groove without standing proud. Send a photo of the block if the old plate is too worn to measure.

What do the 122, 61 and 15 mm figures stand for?

Outside diameter, bore and thickness. The plate is 122 mm across the outside, 61 mm through the bore and 15 mm thick, which is the ring that fits the SCM vacuum block listed as φ122x61x15mm.

What is the plate made of, and what colour is it?

Moulded rubber, gray. The body is a single rubber moulding with no bonded joint across the sealing face, which is the area that fails first on a worn plate.

Do you supply other suction pad sizes and shapes?

Yes. Square pads come in 130x30x17, 120x50x17, 125x75x17, 126x75x17, 145x115x17, 160x115x17 and 140x130x17 mm, plus a φ109x54x18 mm ring, so one order can cover every pod on the table.

Can you make this plate to my own drawing?

Yes. OEM and ODM are both offered: send the drawing, or send one worn plate as the sample, and the size is moulded to it.

How is it packed, and how is it shipped?

Bulk packed in a standard export carton. The outer carton is moisture resistant and high-compression, and its size follows the quantity you order. Shipping is by air, by sea or by express, whichever suits the order.

How do I get a price for the quantity I need?

Send the quantity and we quote against it, because carton size and freight both follow the order volume. The same message can confirm the ring size against your machine.

Which other spares can I order with the plates?

Valve inserts, locating rings and gaskets, in the same shipment. The same range also covers vacuum cups and pads for Homag, Weeke, IMA, Biesse Rover, SCM, Morbidelli and Excitech heads.