Conveyor Chain Track Pads 4060180055 Edgebander Feed Pads for Edge Banding Machine PA Rubber

Worn track pads slowing the feed on a HOMAG edgebander? The 4060180055 chain track pad is the feed pad mounted in the chain conveyor track, and it carries each panel through 4 stations: pre-milling, gluing, pressing and trimming. It is built from PA (nylon) + rubber in red, specified for wear resistance and low noise, and the same pad is catalogued as 4-060-18-0055. Origin China, standard export carton with protective foam, price quoted on request. Either number orders the pad.

Three things stop an edgebander that nobody schedules for: a feed pad worn below its working profile so the panel dips before it reaches the gluing station, a pad gone hard and marking the very edge it should protect, and a chain track stripped down only to find the replacement pad does not fit. All three come back to one consumable.

The 4060180055 conveyor chain track pad is that consumable. It is a replacement feed pad for the chain conveyor track of a HOMAG edge banding machine, and it supports the workpiece across 4 stations — pre-milling, gluing, pressing and trimming. Two numbers identify it: 4060180055 and 4-060-18-0055, the same digits written with and without separators.

Construction is PA (nylon) plus rubber, so one pad does two jobs: the nylon body holds the track profile the chain runs against, the rubber side takes the contact and damps it. That pairing is where the stated wear resistance and low noise come from — an all-hard pad transmits noise, an all-soft one loses its shape.

Colour is red, origin is China, packing is a standard export carton with protective foam, and price is quoted on request.

Checks a parts desk can run against the worn pad in hand before ordering.

• Two numbers, one pad — catalogued as 4060180055 and as 4-060-18-0055, so a drawing, a chain tag or a parts book entry all close on the same item.
• PA plus rubber — two materials in one part: a nylon body for the track profile, a rubber layer for contact, specified as wear resistant and low noise.
• Four stations of support — one pad carries the panel through pre-milling, gluing, pressing and trimming, the 4 stations the specification lists.
• Chain conveyor position — mounted in the chain conveyor track system of a HOMAG edge banding machine, under the workpiece rather than beside it.
• Red, moulded through — the red colour is in the part, so a worn or missing pad shows up on the chain without cleaning it first.
• Replacement, without modification — sold as a replacement for track pad wear, with an accurate track profile noted as giving installation without modification.
• Stable conveyance, stated — the specification names stable conveyance as the reason edge chipping and rework fall on finished panels.
• One number per order — a single-item service part: quantity is quoted against 4060180055, not against a machine serial.
• Export packing — China origin, standard export carton with protective foam, so the red contact face arrives unscuffed.

A worn chain pad leaves two options worth considering: keep running and sort the chipped edges later, or pull the track and stop the line. This pad is the third one.

• Change the pad, keep the chain. The part is a replacement feed pad for the chain conveyor track, so the fix is one consumable on a track system that is reused.
• Two materials, two jobs. A PA (nylon) body holds the track profile and a rubber face takes the contact — the pairing behind low noise and wear resistance, and the reason one pad covers 4 stations.
• Panels held flat through gluing and trimming. Stable conveyance is the stated benefit, and a board riding flat over 4 stations is a board with less edge chipping and rework to sort afterwards.
• Service-part cost, not machine downtime. The pad is listed as an economical part for chain conveyor maintenance, so pad wear is a 1-line item on the parts order instead of a machine intervention.
• Ordered by number, not by serial. 4-060-18-0055 or 4060180055 identifies the pad, so the order starts from the worn pad in your hand and 2 numbers.
• Packed for the trip. Standard export carton with protective foam, so 1 red pad reaches the machine with its contact face intact.

They carry panels along the chain conveyor of an edge banding machine. Each pad is fitted in the chain conveyor track system and supports the workpiece as it passes pre-milling, gluing, pressing and trimming — the 4 stations named in the specification — so the board travels flat and stays square.

Yes, if your machine feeds panels on the HOMAG chain conveyor track system. The pad is listed as compatible with HOMAG edge banding machines and is sold as a replacement conveyor chain track pad; compare it with the pad you are taking off the chain before ordering.

Yes — one pad, two ways of writing it. 4060180055 is the number without separators and 4-060-18-0055 is the same number in grouped form, so either one reaches this item.

PA (nylon) plus rubber. The nylon body carries the track profile and the rubber layer takes the contact, which is why the part is specified as wear resistant and low noise rather than as a plain plastic block.

No. The pad is sold as a replacement for track pad wear, and the accurate track profile is the reason the specification records installation without modification — nothing has to be machined or trimmed on site.

When the panel no longer runs flat over the stations. Pad wear is the failure this part exists to fix: a pad that has lost its profile, gone hard on the contact face or no longer matches its neighbours on the chain is the one to change.

Yes. Quantity is quoted against the part number, so a single pad and a full-chain set are quoted the same way — send 4060180055 (or 4-060-18-0055) with the count you need and the price is quoted against it.

Price is quoted on request — no list price is published for this part. Packing is a standard export carton with protective foam, so the red contact face is protected until the pad goes on the chain.