CCE016 79x72mm Woodworking Machinery Rubber Pad Conveyance Chain Pad for Japan Marnak Automatic Edge Banding Machine

Replacing the chain pads on a Japan Marnak automatic edge banding machine does not need a service call: the pad is a wear part that sits in the chain link. CCE016 is that pad, 79 x 72 mm in rubber, listed at USD 1-2 per piece. It carries the panel through the glue, pressure and trimming stations on the conveyance chain and is a direct replacement for the Marnak pad of the same two dimensions. Measure the worn pad first: 79 mm and 72 mm are the whole fit check.

A worn conveyance chain pad does not break, it goes soft. The panel rides a fraction low, the pressure station presses harder to hold it, and the edge leaves marked on one side and clean on the other. None of that looks like a pad fault, so the pads stay on the track and the trimming blades get blamed.

CCE016 is the pad for Japan Marnak automatic edge banding machines: 79 x 72 mm, rubber, at USD 1-2 per piece. It sits in the chain link and carries the panel through the glue, pressure and trimming stations. 79 mm runs along the direction of travel and 72 mm is the width presented under the panel, so the fit has to be right on both axes.

Rubber is the working part here, not a finish. The pad is the only layer between a steel chain and a finished panel face, so it carries the friction and the marking risk at once: stable grip stops the panel sliding during feed, and the compound is listed as wear resistant with high elasticity.

Pads are a consumable and are normally changed as a chain set. One new pad among worn ones puts a high spot in the track: a fix for a week, then the same fault. Two numbers off the old pad, 79 mm and 72 mm, are the whole fit check.

What the two dimensions, the rubber body and the Marnak listing tell you:

• 79 x 72 mm fit — 79 mm along the chain, 72 mm across the panel contact, both measured off the worn pad.
• Rubber body — the pad flexes in the link under panel load instead of sitting hard like a plastic block.
• Wear resistant compound — specified for continuous running, so the pad takes the wear instead of the chain.
• Grip that holds without marking — stable friction under the panel during feed, so the panel does not slip at the pressure station.
• Marnak compatibility — listed as a direct replacement pad for Japan Marnak automatic edge banding machines.
• Chain-link seat — drops into the existing link position with no machining of the track and no change to chain tension.
• 5,688 mm² of contact per pad — 79 x 72 mm, repeated at every link the track carries.
• Consumable pricing — USD 1-2 per piece, so a full set is a stock order rather than a repair budget.
• One-for-one installation — one pad out, one pad in, with the machine down for the length of the change, not a day.
• High elasticity — the compound returns to shape between panels, so the pad does not take a permanent set under a 79 x 72 mm footprint.

A shop with a soft track has two choices: send panels out until the machine is serviced, or change the pads. Changing them is cheaper by a wide margin.

• The line on the edge goes away.A low pad at one link marks one side of the edge and leaves the other clean; a full set of 79 x 72 mm pads puts every link back at the same height.
• You order by two numbers.79 mm and 72 mm off the old pad is the entire specification, so the order does not need the Marnak parts list.
• No service call, no track adjustment.The pad seats in the chain link with track height and chain tension untouched: one less machine to book in.
• Consumable cost, not repair cost.At USD 1-2 per piece a complete set costs less than the machine time lost diagnosing a soft track.
• The panel face is protected by rubber.The pad is the one rubber layer between the steel chain and the finished panel, so the 79 x 72 mm footprint takes the contact, not the workpiece.
• Scheduled, not reactive.A soft track never breaks, so it is only caught by inspection; a pad measurable at 79 x 72 mm makes that schedule possible.
• Older Marnak machines stay on the line.OEM support keeps a machine on its original track geometry after the pad has left the printed catalogue.

Yes, if the old pad measures 79 mm by 72 mm. CCE016 is listed for Japan Marnak automatic edge banding machines, and those two dimensions are the fit check. Send the machine model with the enquiry if you want it confirmed before ordering.

Count the pads in the chain on your own machine. The number follows the track length, which is why CCE016 is priced per piece at USD 1-2 rather than sold only as a set.

Yes, change the set. A new 79 x 72 mm pad sitting beside worn ones becomes a high spot in the track, so the fault is back within weeks rather than fixed.

Rubber. The product data lists rubber as the material, with a wear resistant compound and high elasticity for a long service life.

Because the pads have lost friction, not because pressure is too low. Worn rubber stops gripping, the panel slides during feed, and the edge line goes out of parallel.

Yes, OEM support is listed for this part. Send the measured length and width of the old pad and it can be quoted; 79 x 72 mm is the catalogued size for CCE016.

They are confirmed per order, because the listing gives the piece price only. CCE016 is listed at USD 1-2 per piece; send the quantity you need and those four terms come back with the quotation.

Three things: 79 mm and 72 mm measured off the old pad, the number of pads per chain, and the machine model. That is enough to quote CCE016 at USD 1-2 per piece.