Edge Banding Machine Chain Pad 70x37xH37.5 for SCM 29L0184850H Edgebander Spare Parts

Replacing a worn chain pad on an SCM edgebander? The 29L0184850H is the conveyor chain pad that carries each panel past gluing and trimming, and it measures 70 x 37 x H37.5 mm — 70 mm long, 37 mm wide, 37.5 mm high. The contact face is grey rubber on a black plastic base. One part number covers one pad, so a worn block is swapped where it sits and the chain is never pulled. Price is quoted on request against the quantity you need.

A chain pad does not fail loudly. The panel starts rocking before the gluing station, the banding sits a fraction out of square, and the operator slows the feed to hide it. On an SCM edgebander the panel rides on pads fixed to the conveyor chain, so a pad that has lost height shows up downstream as a scrap edge.

The 29L0184850H is that pad: a replacement chain pad for SCM edgebanders, catalogued as part number 29L0184850H and sized 70 x 37 x H37.5 mm; 70 mm long, 37 mm wide, 37.5 mm high. The H marks the height, so that figure reads on the height axis. Get one of the three wrong and the pad either will not seat or sets the panel at the wrong level.

The contact face is rubber, supplied grey, on a black plastic base. The two-part build puts a compliant face against the panel and a rigid base against the chain link; the colour split is the identity check, so the worn block is matched before the caliper comes out.

As a wear part it is bought by part number and size, not by machine serial: quote 29L0184850H with the measurements and the order is placed from the block in your hand. Price is quoted on request. It is classed as a woodworking spare part for SCM edgebanding machines.

What the part number fixes, and what to check on the chain:

• Part number first — 29L0184850H is what the order is placed on, and it covers one pad, not a chain set.
• 70 x 37 x H37.5 mm — 70 mm long, 37 mm wide, 37.5 mm high, read in that order off the block; the H marks the height figure.
• Grey rubber face — the pad is rubber on a plastic base, with a grey contact face that meets the panel.
• Black plastic base — the rigid part sits against the chain link and holds the working height.
• SCM edgebander fit — made as spare parts for SCM edgebanding machines, so the 70 mm footprint is sized for their conveyor chain, not trimmed on site.
• Conveyor chain position — the pad rides on the chain and carries the panel through the feed, not beside it.
• One support height — every pad holds the panel 37.5 mm above the link, so a worn one shows up as the block that no longer matches its neighbours.
• Wear part, bought singly — one part number, one pad, so a single worn block is changed without buying a chain set.
• Checked with two tools — a caliper for 70 x 37 x 37.5 mm and an eye for grey on black; no machine serial needed.

A worn pad leaves two choices: keep running and sort the scrap edge later, or strip the chain to change one block. This pad is the third option.

• Change the block, leave the chain on. Because the pad is a separate chain part, one worn block is replaced in place — no chain stripped and no tension reset.
• One height across the conveyor. With every pad at 37.5 mm, the panel is supported at the same level on each link, so the board stops rocking on its way to the trim station.
• Numbers you can measure. 70 x 37 x 37.5 mm and grey rubber on a black plastic base are both on the record, so a new pad is checked against the old one before it goes on the chain.
• No variant list to work through. One part number, 29L0184850H, covers the pad, so the order comes off the block in your hand and not off a machine plate.
• A wear item quoted per order. Price is quoted against the quantity you need, so a top-up of three pads and a full-chain order are quoted on the same part number.
• Fit is to the machine family. The pad is made for SCM edgebanders, so the 37.5 mm height and the 70 x 37 mm footprint match the chain instead of being shimmed to suit.

Yes, if the pad you are replacing measures 70 x 37 x 37.5 mm. The pad is made for SCM edgebanders and mounts on the conveyor chain; measure the worn block before ordering, because those three figures decide the fit.

70 mm long, 37 mm wide and 37.5 mm high — written 70 x 37 x H37.5 mm, where the H marks the height figure. On the block that reads as length along the chain, width across the link and height above it.

Rubber and plastic. The contact face is grey rubber and the base is black plastic, so the grey face is the side that meets the panel and the black base is the side that sits on the chain link.

29L0184850H. The listing is catalogued under that one number, and it is the same number printed alongside the 70 x 37 x H37.5 mm size, so quoting both removes any doubt about which pad is wanted.

You can order a single pad. One part number covers one pad, so a worn block is replaced on its own; count the pads on your chain if you want to price a full change in one go.

Compare it against 37.5 mm. A block that measures under that figure, or shows a flattened or polished contact face, is the one to change — and because pads wear together, the blocks either side are usually close behind.

Yes — the same part is described as a chain pad and as a conveyor pad. It is the block fixed to the conveyor chain of an SCM edgebander, and the panel rides on it through the feed.

Price is quoted on request; no list price is published for this part. Send part number 29L0184850H and the quantity you need, and the price is quoted against that order.