Horizontal Facing Unit Edgebander Cross-cut Assembly Edge Banding Machine End Cutting Units End Trimming

Replacing a worn end trimming station on an edgebander? The XESPOT-A horizontal facing unit is the complete cross-cut assembly that mounts on the upper beam of an edge banding machine. It trims panel ends over a 10–60 mm panel thickness range, on a 20–35 mm running distance, at 0.2–0.5 MPa working pressure. Overall size is L1300 × W410 × H570 mm. Fast cutting speed and high precision are the two stated advantages. It is supplied as a spare part for edgebanding machine assembly, so the whole trimming station is replaced as one item.

An end trimming unit wears out in three visible ways: the cross-cut stops flushing the panel end and leaves a whisker of overhang, the operator takes a second pass where one pass used to do, and the worn assembly starts shifting on the beam. The XESPOT-A horizontal facing unit is the assembly that replaces all three at once.

This is a horizontal facing unit for edgebanders, listed under three names — cross-cut assembly, end cutting unit and horizontal end trimming unit — so it can be matched against whichever name your parts list uses. It installs on the upper beam of an edge banding machine and is supplied as an assembly for edgebanding machine mounting, not as a bare blade.

Coverage is set by panel, not by guesswork: 10–60 mm panel thickness, a 20–35 mm running distance that carries the trim stroke past the panel end, and 0.2–0.5 MPa working pressure at the inlet. Overall dimensions are L1300 × W410 × H570 mm, and the 1300 mm body length is the number to check against the space already cut into your beam.

Cutting speed and precision are the two advantages stated for this unit. It is a spare part, so one SKU covers the whole trimming station and a second machine running the same station is covered by the same part number. Price is quoted per enquiry.

Five numbers and three names decide whether a replacement end trimming unit lands on your beam and holds its cut.

• Upper beam mounting — built for the upper beam of an edge banding machine, the location the end trim station is designed around, so it replaces the station in place.
• 10–60 mm panel thickness — one unit covers board from 10 mm to 60 mm, so a mixed production run needs no second trimming station.
• 20–35 mm running distance — the trim stroke travels 20 mm to 35 mm, the range that carries the cut past the panel end.
• 0.2–0.5 MPa working pressure — the unit runs between 0.2 MPa and 0.5 MPa, set once at the regulator.
• L1300 × W410 × H570 mm — 1300 mm long, 410 mm wide and 570 mm high, so the envelope can be measured against the beam before the order.
• Horizontal facing action — the unit faces the panel end on the horizontal axis, the cut that removes the overhanging edge material after the band is applied.
• Cross-cut assembly — supplied as an assembly rather than a single knife, so the station is replaced in one step.
• Three part names, one SKU — horizontal facing unit, cross-cut assembly and end cutting unit all resolve to XESPOT-A, which makes the part easy to confirm against a parts list.

When the end trim station goes off, a shop has two choices: keep running panels and rework the overhang by hand, or stop the line and wait for a unit. The XESPOT-A removes that choice.

• One part number covers the station. The unit is a complete cross-cut assembly, so you replace the trimming station once instead of chasing individual components and their wear.
• One unit covers the board range. With 10–60 mm panel thickness, the same station runs thin cabinet board and 60 mm panels, so the spares shelf holds one part number.
• The stroke is matched to the job. A 20–35 mm running distance carries the cut past the panel end, which is the stroke length the facing action needs.
• The envelope is published. L1300 × W410 × H570 mm is printed on the sheet before you buy, so the fit on the upper beam is checked against a number, not a guess.
• Air pressure stays low. 0.2–0.5 MPa is the whole working range, so the unit runs off the shop air line already at the machine.
• Fitment is a name match. Because horizontal facing unit, cross-cut assembly and end cutting unit are the same SKU, a parts list written in any of the three names resolves to XESPOT-A.

Yes, if your machine takes an upper beam mounted end trim station. The XESPOT-A installs on the upper beam of an edge banding machine and measures L1300 × W410 × H570 mm, so compare that envelope with the space on your beam.

10 mm to 60 mm. That is the full panel thickness range published for this unit, so the same station covers thin cabinet board and thicker panels.

0.2–0.5 MPa. That is the whole working range, so it runs from the air line already at the machine, set once at the regulator.

Yes. Horizontal facing unit, cross-cut assembly, end cutting unit and horizontal end trimming unit all describe the same XESPOT-A assembly.

20–35 mm. The running distance is the trim stroke, so it has to travel past the panel end to clear the overhang in one pass.

The whole assembly. XESPOT-A is supplied as an assembly for edgebanding machine mounting, so the trimming station is replaced as one item rather than as a loose knife.

1300 mm long, 410 mm wide and 570 mm high. The 1300 mm length is the dimension to measure first, because it runs along the beam.

Send an enquiry with your machine model and the part you are replacing. Price is quoted per enquiry, and the SKU to quote is XESPOT-A.