Tshare XE-500 Edge Banding Machine Magnetic levitation Side Drilling Device Edgebanding Machine Units

Need side holes drilled in a panel without a second pass through a boring machine? The XE-500 adds a side drilling station to the edge banding line. Adaptation speed 0–30 m/min, panel thickness 10–60 mm, effective stroke 290 mm, peak thrust 1008 N, continuous thrust 276 N. The head is a magnetic levitation type and mounts horizontally on the edge banding machine base; the electric control box stands separately at 400 × 260 × 965 mm. Unit footprint is 590 × 465 × 417 mm — measure that against your base plate before ordering.

A shop that bands a panel and then drills its side holes runs into the same three things: the panel leaves the line and comes back for a second operation, the second setup has to be squared to the first one, and the hole position ends up depending on who loaded the panel. The XE-500 is the unit that puts the drilling station on the banding line instead.

It is a magnetic levitation side drilling device: a horizontal drilling head built to mount on the base of an edge banding machine and drill side holes in the banding pass. Adaptation speed is 0–30 m/min, so the unit can be set to the feed speed the machine already runs. Panel thickness covers 10–60 mm, and effective stroke is 290 mm, the travel available for placing the hole along the edge.

Thrust is quoted as two figures because it is two different forces: 1008 N peak thrust when the bit enters the panel, and 276 N continuous thrust held through the rest of the stroke. Board types listed for the unit are MDF, particleboard, plywood and solid wood panels.

The drilling unit measures 590 × 465 × 417 mm and installs horizontally on the edge banding machine base. Electrics sit in a separate cabinet, 400 × 260 × 965 mm. Price is quoted on request.

Each item below is a figure or a component from the unit's product data, not a performance claim.

• Maglev head — the head is the magnetic levitation type named in the XE-500 listing.
• 0–30 m/min adaptation — the unit is set to the feed speed the bander runs, so drilling and banding share one line speed.
• 10–60 mm panel range — the board thickness listed for the device, from 10 mm to 60 mm.
• 290 mm effective stroke — the travel the head has for positioning the hole along the panel edge.
• 1008 N peak / 276 N continuous — peak force at bit entry, holding force through the remainder of the stroke.
• Horizontal base mounting — the unit mounts on the edge banding machine base, on a footprint of 590 × 465 × 417 mm.
• Separate control cabinet — electrics live in a 400 × 260 × 965 mm box; the operating panel and emergency stop sit on its top face, as the photos show.
• Four board types — the listed materials: MDF, particleboard, plywood and solid wood panels.
• Servo motor on the head — the servo drive is mounted on the drilling head itself, as the detail photos of the unit show.
• One re-order number — the unit is listed under part number XEX4ZXK-500, so a repeat order does not depend on a photo.

Without a side drilling station the choice is a second operation on another machine, or a hand drill at the bench.

• The second operation comes off the route. The panel is drilled in the banding pass, so it is loaded once, on one reference edge, instead of twice.
• One line speed, not two. 0–30 m/min is set to what the bander already runs; the head adds no separate speed to balance.
• The board range runs 10–60 mm. Panels from 10 mm to 60 mm pass the same head, so one unit covers that whole span.
• Hole placement comes from the stroke. 290 mm of effective travel is the window a hole can be set in along the edge — set once per job.
• Force is there at entry. 1008 N peak thrust is what the bit gets as it touches the panel; 276 N continuous is what carries the rest of the stroke.
• Base footprint, not a second machine. The unit takes 590 × 465 × 417 mm on the machine base; the electrics stand in their own 400 × 260 × 965 mm cabinet.
• Re-ordering takes one number. XEX4ZXK-500 identifies the unit, so the second order is the same unit as the first.

Only if your machine base can carry the unit's 590 × 465 × 417 mm footprint and the line runs inside 0–30 m/min. The unit mounts horizontally on the base, so measure the existing base plate and the running feed speed first. Both figures are in the parameter table above.

10–60 mm. That is the panel thickness range listed for the device, and it is a declared range, so a board inside it is what the unit is specified for — not a board outside it.

290 mm effective stroke. That is the travel available for placing the hole along the panel edge, so the stroke sets the window you can position in, not the distance to the banded edge.

No. 1008 N is peak thrust, the force at the moment the bit enters the panel. The continuous figure is 276 N, which is what is held through the rest of the stroke.

Yes. The electric control box is its own cabinet at 400 × 260 × 965 mm, standing apart from the drilling unit. The operating panel and emergency stop are on the top face of that box.

MDF, particleboard, plywood and solid wood panels. Those four are the board types listed for the unit, and the thickness limit is the same 10–60 mm for all of them.

Horizontally, on the base of the edge banding machine. The drilling unit is the part that mounts to the base; the electric control box is placed separately and wired to it, so the base needs room for 590 × 465 × 417 mm.

Price is quoted on request, against the quantity you need. Quote model XE-500 and part number XEX4ZXK-500 with your enquiry, plus your panel thickness range and line speed, so the unit goes out matched to the machine it lands on.