Edge Banding Machine Scraping Unit Replacements Edgebanding Machinery Units ( 2-012-80-3350 2-012-80-3360 also available )

Need the glue line gone from the panel edge without replacing the whole scraping station? The XE GB-C is the scraping unit itself. It mounts at the upper and lower profile positions of an edge banding machine, takes panels 10–60 mm thick and >45 mm long, and follows the line at 0–30 m/min on 0.2–0.5 MPa working air. The unit measures 390 × 240 × 450 mm. Original numbers 2-012-80-3350 and 2-012-80-3360 are also available, and the price is quoted on request per unit number.

A scraping station is where a clean edge is won or lost, and it goes wrong three ways. The glue line survives the trim, so the edge reads as a grey stripe under raking light. The worn part is one assembly, while the machine carrying it is still sound. And a service visit costs more panel time than the unit costs to buy. The XE GB-C is that one assembly: a replacement scraping unit for edge banding machines, fitted at the upper and lower profile positions.

Its job starts where trimming stops. Sitting at both profile positions, it removes the excess glue line left along the edge and refines the surface behind it, so the edge comes out clean, smooth and even instead of tacky and stepped. Installation is vertical, so it enters the machine in one plane and serves both maintenance replacement and machine upgrade. It runs panels from 10 mm to 60 mm thick, and panel lengths above 45 mm.

Adaptation speed is 0–30 m/min and working air is 0.2–0.5 MPa, so the unit follows the trimmer ahead of it rather than setting the pace. Overall size is 390 × 240 × 450 mm — narrow enough that access around both profiles stays open. Original numbers 2-012-80-3350 and 2-012-80-3360 are available for the same stations.

Each line below is a number or a fit detail written on this unit.

• Upper and lower profile positions — specified for both profile positions of an edge banding machine, so one drawing covers the pair of mounting points that wear together.
• 10–60 mm panel range — one unit spans the thinnest 10 mm back panel and the thickest 60 mm door on the same line.
• 45 mm minimum length — it is rated for panels longer than 45 mm, which keeps drawer sides and short door parts inside the run.
• 0–30 m/min line speed — the window starts at 0 m/min, so the unit is on the machine at start-up and at every feed rate to 30 m/min.
• 0.2–0.5 MPa working air — a 0.3 MPa window read straight off the gauge at the station.
• Vertical installation — the unit enters in one plane, so a fitter works from one side of the profile instead of dismantling around it.
• 2-012-80-3350 and 2-012-80-3360 — both original numbers are offered alongside XE GB-C, so a hall running either keeps one spares route.
• 390 × 240 × 450 mm body — that is the envelope to check against the guard and frame opening before ordering.
• Glue line removal after trimming — the unit works behind the trimming station, so the excess glue trimming leaves is off before the panel reaches polish.

Once a scraping unit dulls, the choice is usually to live with the glue line, call a service van, or buy a whole station.

• The station stays bolted to the line. Only the scraping unit leaves the machine; the trimming head, frame and drives are not touched, so the accurate parts are never re-set.
• One part number, 10 mm to 60 mm. Thin back panels and 60 mm doors pull the same unit from the shelf, so the spares bin holds one line.
• Short panels keep their slot. A 45 mm minimum length keeps drawer sides and door parts in the run instead of being finished by hand.
• Speed follows your line, not the part. 0–30 m/min adaptation speed means the line is not slowed to suit a scraper.
• The air setting is on the gauge. 0.2–0.5 MPa can be read, repeated and handed over between shifts without guesswork.
• Fit is checked before the panel is. Vertical installation and 390 × 240 × 450 mm reduce the pre-order check to a height and a side clearance.
• Both original numbers stay available. 2-012-80-3350 and 2-012-80-3360 sit alongside XE GB-C, so a mixed machine hall comes from one supplier.
• Price is quoted against your order. The unit is priced per enquiry on the unit number and quantity, so a stock spare and a single replacement are quoted alike.

An edge banding machine, at the upper and lower profile positions. The unit is installed vertically at those two points, behind the trimming station, so it is a spare for edge banding machines rather than for a standalone polisher.

10–60 mm thick, and any panel longer than 45 mm. Both figures are on the unit's own specification, so the same part covers thin back panels and 60 mm doors without a change of scraper.

0.2–0.5 MPa working pressure. That is a 0.3 MPa window, so the regulator setting is read from the gauge at the station rather than set by feel.

0–30 m/min adaptation speed. The window starts at zero, so the unit stays on the machine at start-up and at every feed rate up to 30 m/min.

390 mm long × 240 mm wide × 450 mm high, mounted vertically. Check that height and the side clearance against the guard and the frame opening before ordering.

Yes — both of those original unit numbers are available alongside the XE GB-C. Send the number stamped on your machine and the position it sits in, and the match is confirmed against it.

Glue. The unit removes the excess glue line left after trimming and refines the edge surface behind it; the banding itself has already been applied and trimmed by the stations ahead.

Yes. The unit is listed for maintenance replacement and for machine upgrades, and vertical installation is what lets it go onto an existing upper or lower profile without reworking the frame.