Tshare Edgebander Rapid Glue Melting Machine

Need to stop topping up a small glue pot every hour? The XE2HM-A holds 5 kg of EVA hot melt and is rated for up to 12 hours of continuous supply, so one fill covers a shift. Glue is fed pneumatically at 6 Kgf/cm², the whole glue path is held at 160 °C, and the heater draws 900 W. The unit weighs 14.5 kg and measures 500 × 170 × 759 mm, so it mounts on an existing upper glue tank position without a frame rebuild. Tungsten steel nozzle, level sensor, copper solenoid valve.

An edgebander earns money only while it runs, and glue is the usual reason it stops: a small pot runs dry mid-batch, someone refills it by hand, the line waits. Glue held too long at temperature scorches on the tank wall and later breaks loose as grit. When the level drops quietly, panels leave the press with starved edges found only after trimming. The XE2HM-A addresses all three.

It is a rapid glue melting unit for an upper glue tank, replacing the small integrated pot on an automatic edgebander. The tank holds 5 kg of EVA hot melt, and glue is pushed to the applicator pneumatically at 6 Kgf/cm² rather than trickling down by gravity. Full-length heating holds the glue path at 160 °C, so the melt stays liquid from tank to nozzle, and the tungsten steel nozzle resists the wear that opens a brass tip.

The unit draws 900 W, measures 500 × 170 × 759 mm and weighs 14.5 kg, light enough for one person to lift onto the machine frame. One 5 kg fill is rated for up to 12 hours of continuous supply, so a shift passes without a refill. The body carries a die-cast aluminium aviation plug and a copper solenoid coil, and the handle stays cool after a run.

What separates this unit from the pot already on your machine:

• Upper tank, 5 kg of EVA — one fill carries the machine through a full shift, rated up to 12 hours of continuous supply.
• Pneumatic glue feed at 6 Kgf/cm² — air pressure pushes melt along the line instead of relying on gravity, so the bead stays full after a pause.
• Full-length heating to 160 °C — tank, line and nozzle are held at melt temperature, so the cold plug that blocks a short-path pot cannot form.
• Tungsten steel gourd nozzle — a wear-resistant tip keeps the outlet round; a rounded brass tip smears glue instead of laying a bead.
• Level sensor with overheat lockout — glue level is monitored and repeated reheating is cut, so the EVA is not cooked twice in the same tank.
• Pure copper solenoid valve — copper coil on the air circuit gives stable switching for pneumatic dosing at 6 Kgf/cm².
• Die-cast aluminium aviation plug — sealed connector housing, water and flame resistant at the plug joint.
• Heat-resistant carry handle — the 14.5 kg unit lifts off the frame by hand and can be moved between two edgebanders.
• 900 W heater — brings a 5 kg EVA charge up to the 160 °C melting temperature, then holds it there through the shift.

Most shops face the same choice: keep refilling a small pot and lose minutes every hour, or buy a second edgebander to keep two lines fed. A 5 kg upper tank removes that choice.

• A shift without a refill. 5 kg of EVA at up to 12 hours of rated supply turns a day of interruptions into one top-up at the end of the shift.
• Glue you do not throw away. A constant 160 °C and a sensor that blocks repeated heating keep the melt from scorching, so what is in the tank stays usable instead of being scraped out.
• Edges that do not starve. Pneumatic feed at 6 Kgf/cm² holds the bead through the first panel after a stop, which is where starved edges usually appear.
• A nozzle you replace, not ream. Tungsten steel resists the wear that rounds off a brass tip, so the outlet stays the size it left the factory.
• One person can fit it. 14.5 kg and 500 × 170 × 759 mm means no crane and no frame rebuild, and the aviation plug puts air and heat back on the same way every time.
• Runs on the air you already have. 6 Kgf/cm² is normal shop air and the 900 W heater is one load, so the machine keeps its original footprint.

An automatic edgebander with an upper glue tank position. The XE2HM-A is a complete melting and feeding unit for that position: 5 kg EVA tank, pneumatic feed at 6 Kgf/cm², full-length heating to 160 °C.

Up to 12 hours of continuous supply at normal edgebanding consumption. Fill the 5 kg tank at the start of a shift and the line runs to the end of it without a refill.

Yes, that is what the heating and the feed design are for. The tank, line and nozzle are held at 160 °C, air pressure at 6 Kgf/cm² pushes the melt forward, and the tungsten steel nozzle resists the wear that opens a normal tip.

EVA hot melt. The 5 kg tank, the 160 °C melting temperature and the nozzle are set up for EVA edgebanding glue.

Because an upper tank feeds the applicator with gravity plus 6 Kgf/cm² of air, which keeps the glue path short and the bead full. It also puts the fill lid at working height.

It can take over the melting and feeding job in an upper tank position. Send the edgebander model and a photo of the current tank so the mounting and air connection can be confirmed before you order.

Shop air at 6 Kgf/cm² and the heater's own 900 W circuit. The aviation plug and the heat-resistant handle are there so the unit can be lifted off by hand for cleaning.

Price is by quotation. Send the edgebander model and the quantity you need and you will get a quote for the XE2HM-A with the glue tank and nozzle you want.