Pneumatic Glue Pot For Edgebander - Dual Tank System And Dust Removal Function

Need to change glue colour without draining a tank mid-run? The XEIQD-B pneumatic glue pot for edgebander carries two independent tanks, so a second glue or colour stays online. A Teflon inner wall layer stops glue bonding to the pot wall, and the built-in dust removal function pulls dust out of the glue application area before it reaches the glue line. Control is pneumatic. Manual and single tank versions are available, forward direction is standard, and a reverse version is offered. Send photos of your old pot and fitment is matched before shipping.

An edgebander glue pot usually fails a workshop in three ways: one tank means draining and flushing hot glue on every colour change, dust from trimming lands on the freshly glued edge, and carbonised glue on the pot wall has to be chiselled out at the end of every shift. The XEIQD-B is built to remove all three.

This is a pneumatic glue pot for edgebanders with a dual tank system and a built-in dust removal function. Two tanks keep two glues or two colours at working temperature, so changeover is a switch between tanks, not a drain and a flush. The inner wall layer is Teflon, so cured glue releases instead of bonding, and the daily clean is a wipe.

Direction is forward as standard, with a reverse version available. A manual version and a single tank version exist on the same platform, and a glue pot for Homag edgebander is also available. Fitment is confirmed from your own photos: send pictures of the pot you are replacing and the ports and mounting are checked before the order is released.

Six things decide whether a glue pot survives two shifts on an edgebander: tank access, wall material, dust control, air logic, direction and whether the fit matches your machine.

• Pneumatic control — glue feed is driven by air pressure, so flow is set at the regulator and no drive motor sits in the glue area.
• Dual tank system — two independent tanks hold two glues or two colours at temperature, so changeover needs no drain, no flush and no cooldown.
• Teflon inner wall layer — the pot wall is lined with Teflon, so cured glue lifts away in one piece instead of bonding to steel.
• Dust removal function — dust and chips are taken away at the glue application area, so debris does not settle into the glue line before edging is pressed on.
• Forward direction, reverse available — the standard pot runs forward; the reverse version uses the same body for opposite-hand lines.
• Manual version — a manual pot is offered on the same platform for shops that do not run compressed air to every glue station.
• Single tank version — a single tank pot is offered for one-glue shops, so you do not pay for a second tank you never fill.
• Homag replacement fit — a glue pot for Homag edgebander is also available, and valve insert, locating ring and gaskets are supplied as replacement parts.

There are only two options when a glue line goes down: keep flushing one tank on every colour change, or stop the machine and wait. The XEIQD-B removes that choice.

• Colour changes stop costing a shift. Two tanks stay at working temperature, so the second glue is ready the moment the order changes and the first tank keeps running.
• Cleanup drops to a wipe. With a Teflon inner wall layer, cured glue lifts off instead of bonding, so the end-of-shift chisel and scraper routine disappears.
• Dust is captured at the glue line. The dust removal function works at the application area, which protects adhesion on the edge you have just glued.
• No drive motor in the glue area. Pneumatic control leaves seals and valves as the wear parts, and valve insert, locating ring and gaskets are stocked as replacements.
• One platform, three configurations. Pneumatic dual tank, manual and single tank versions share the same body, so a second machine on your floor uses the same spares.
• Fit is confirmed before you pay freight. You send photos of your current pot, and ports, direction and mounting are checked against it first.

Yes. Two independent tanks hold two glues or two colours at working temperature, so a colour change is a switch between tanks instead of a drain and a flush.

It fits once we match it to your existing pot. Send pictures of the glue pot you are replacing and the ports, direction and mounting are checked before the order is released.

No. A manual version and a single tank version are available on the same platform, so you order the configuration your shop actually runs.

Forward is the standard direction. A reverse version is available for lines that need opposite-hand glue application.

The inner wall layer is Teflon. Glue releases from Teflon instead of bonding to it, so the pot is cleaned by wiping rather than scraping.

It takes dust and chips away at the glue application area. Keeping that area clear means the glue meets clean board and clean edging instead of a dust layer.

Yes. A glue pot for Homag edgebander is also available and is quoted the same way as the standard pot, with fitment checked from your photos.

Seals, valve inserts and gaskets are the parts that wear. Valve insert, locating ring and gaskets are supplied as replacement parts, so the pot stays serviceable.