Pneumatic Glue Pot For Woodworking Edgebanding Machine - Dust Removal Glue Tank

Replacing a glue pot on an edge bander should cost a pot, not a gluing unit. Item XEIQD-B is that pot: pneumatic action with a manual version also available, PUR and EVA adhesives on the same tank, 10-15 min melting time, 2 kW rated power, 1.0 fine coated mesh knurling for glue saving and precise gluing, plus a dust removal function at the gluing area. Packed in a standard carton box. Price on request.

A bad glue line does not stop an edge bander, it ships rejects. In the shops that keep a spare pot on the shelf, the same three things come back: the pot is quoted as a whole gluing unit instead of the tank, the replacement arrives without its pneumatic side so the air lines are re-run by hand, and dust reaches the glue bead before the band does.

Item XEIQD-B is the pneumatic glue pot for woodworking edgebanding machines, listed with a dust removal glue tank function. It runs on pneumatic action, a manual version is also available, and it takes both PUR and EVA adhesive. Melting time is 10-15 min and rated power is 2 kW.

The glue-applying surface is 1.0 fine coated mesh knurling, a coated mesh knurl that meters the adhesive film instead of flooding it, which is why the spec sheet lists it for glue saving and precise gluing. The dust removal function works at the gluing area itself, so the bead meets a clean edge rather than a dusty one.

It is a spare part for woodworking edgebanding machines and ships in a standard carton box. The pictured assembly carries its own air manifold, braided air lines and wiring harness. Price on request.

What the pot is, in the terms a maintenance fitter asks for:

• Pneumatic action - the pot is air driven, as listed; a manual version is available where the machine has no air.
• PUR and EVA on one tank - 2 adhesive families run on the same pot, so EVA work and PUR work do not need two spares.
• Melt in 10-15 min - a cold pot reaches working temperature in 10-15 min, the gap between shift change and the first good panel.
• 2 kW rated power - 2 kW is the figure listed for the pot, and it sets that melt time.
• 1.0 fine coated mesh knurling - a coated mesh knurl meters the film, listed for glue saving and precise gluing.
• Dust removal function - dust is cleared at the gluing area, so the bead bonds to the board and not to a layer of dust.
• Air side made up on the body - braided lines and push-fit fittings sit on the pot, so it goes back as 1 assembly.
• Vented top cover and brass outlet - the slotted cover and the brass outlet head are the two points a fitter inspects first.
• Standard carton box - packed in a standard carton, so it can travel by courier or be consolidated with a machine order.

When the glue line drifts, the choice is a gluing unit, an outside repair or a pot on the shelf. This is the third option, and this is what it buys.

• Replace the pot, not the unit. Tank, body and air side arrive as one assembly, so the spend stays at pot level.
• Two adhesives, one spare. PUR and EVA both run on the same XEIQD-B pot, so one spare covers both jobs on the floor.
• Cold start in 10-15 min. A melt is ready inside 15 min of switch-on, the difference between a lost hour and a running line.
• Less glue per metre. The 1.0 coated mesh knurl meters the film, so one bag of adhesive covers more panels.
• Dust stops being a variable. The pot's own dust removal function clears the gluing area, removing the one fault a fitter cannot see from outside.
• Fits the air you already run. Pneumatic action means no separate drive to install; where there is no air, the manual version is quoted instead.
• Swap in one connection. Air lines and harness are made up on the body, so a change is 1 bracket and 1 plug, not a re-pipe.
• A tank number to quote. Quote XEIQD-B and the adhesive in use, and the pot is identified without a drawing or a photo.

It is the tank that melts the adhesive and meters it onto the edge, driven by air instead of by hand. On the XEIQD-B the tank, the air manifold and the outlet are one assembly, so the pot goes back on the machine in one piece.

Yes. Both PUR and EVA are listed as suitable adhesives for this pot, so a shop running both does not need two different tanks. State the adhesive when ordering so the matching version is quoted.

10-15 min from cold to a working melt. Plan the switch-on at shift start and the pot is ready before the first board reaches the gluing station.

Yes, the pot is pneumatic. If your machine has no air circuit, a manual version is also available, and the two are ordered as separate items.

It clears dust at the gluing area, before the adhesive meets the edge. Dust on the edge is the usual reason a bead looks right at the pot and fails at the band, so clearing the area removes that variable rather than masking it.

It meters the glue film. The coated mesh knurl on the glue-applying surface spreads a controlled film instead of a heavy one, which is the reason the spec lists both glue saving and precise gluing rather than one or the other.

2 kW is the rated power listed for this pot, and it is the figure behind the 10-15 min melt time. Confirm the rating against your machine before the pot is wired in.

In a standard carton box, so it can ship by courier on its own or be consolidated with a spare-parts order. Price comes on request: send item number XEIQD-B, the adhesive and the quantity.