4-008-41-0227 4008410227 HEATING CARTRIDGE D12.5 L205 Glue Pot Heating Tube

Glue pot not holding temperature on a Homag edgebander? The 4-008-41-0227 / 4008410227 heating cartridge is the heater that sits in the pot: 12.5 mm outside diameter, 205 mm long. Fit is decided by those two numbers, so measure the old cartridge and compare them with the printed values instead of ordering by eye. It is the cartridge only — pot body, thermostat and glue sensor stay on the machine. Both number formats order the same part, custom diameter and length are supported, and price is quoted per inquiry.

A glue pot that runs cold rarely fails loudly. The band lifts at the panel end, the melt comes away in strings instead of one bead, and the rest of the shift is finished with a hand roller. Then the failed cartridge is pulled out, the label is baked blank, and the replacement is ordered by tape measure.

4-008-41-0227 / 4008410227 is the cartridge that melts glue in the pot of a Homag edgebanding machine. Its whole fit specification is two numbers: 12.5 mm outside diameter and 205 mm length. The diameter decides whether the cartridge seats in the pot bore; the length decides how far it reaches past the bore to its lead end.

It is the heater only. Pot body, thermostat and glue sensor stay on the machine, so the repair is a cartridge swap and not a glue-unit rebuild. The number itself is printed in two formats, 4-008-41-0227 on one carton and 4008410227 on another, and either format orders the same item.

Customisation is supported, so a pot that takes a different diameter or a longer cartridge is quoted to your drawing rather than refused. Price is by inquiry. The same supply line carries the rest of a woodworking shop's machine parts, which keeps an edgebander rebuild to one purchase order instead of five.

Every point below is a value you can check against the cartridge in your hand:

• 12.5 mm diameter — the bore value printed with the part, so a caliper reading is compared with a number rather than an impression.
• 205 mm length — L = 205 mm overall, the dimension that decides how deep the cartridge sits and where its lead end finishes.
• Two number formats — 4-008-41-0227 and 4008410227 order the same cartridge, so a spares list carrying either line is correct.
• Glue pot duty — the cartridge melts the glue that bonds the band to the panel edge; that is the one job it is made for.
• Homag fitment — listed for Homag edgebanding machines, so the machine side of the fit is already answered.
• Heater only — pot body, thermostat and glue sensor stay in service; the order is one cartridge, not a glue unit.
• Straight cartridge body — a 12.5 x 205 mm cylinder, so the fit check is a bore and a depth.
• Customisation supported — state a different diameter or a different length and the cartridge is quoted to that size.
• Three facts close an order — part number, 12.5 mm, 205 mm; nothing else has to be measured twice.
• One supply line — the same supplier carries various woodworking machine parts, so one order covers the pot and the machine.

When a glue-pot cartridge dies, the usual options are a service visit, a whole glue unit, or a part ordered by eye and returned by post.

• A bore number instead of a guess. The diameter is published as 12.5 mm, so the decision is made with a caliper against a printed value, not a tape measure.
• 205 mm settles the depth. Length is stated with the part, and it is what decides whether the new cartridge reaches the pot wall that the old one reached.
• Two labels, one line item. Whether the spares list says 4-008-41-0227 or 4008410227, the order closes on the same part, so a mixed fleet does not need two stock codes.
• The pot stays on the machine. Pot body, thermostat and glue sensor are not in the order, so a cold pot costs one cartridge, not a glue-unit rebuild.
• Custom lengths are a specification, not an exception. Diameter and length are quoted to your drawing, which matters when a pot has been modified or the original number is worn away.
• Fit is checked before the pot cools. Three facts — part number, 12.5 mm, 205 mm — confirm a match without pulling the glue unit apart twice.
• One order restocks the line. The same supply line covers other woodworking machine parts, so the next item on the list needs no second supplier.

Yes, if the bore and the depth match the two published values: 12.5 mm diameter and 205 mm length. Pull the old cartridge, measure its outside diameter and its overall length with a caliper, and compare both figures before ordering — a body 0.5 mm over size will not seat in the pot bore.

Yes. The two formats are one cartridge, printed differently on different cartons. Quote either line on the inquiry and the same item is picked; the spares list does not need two stock codes for it.

Measure the outside diameter across the body, the overall length end to end, and read the number printed on the body as a cross-check. The values to compare with are 12.5 mm and 205 mm; if the old part is worn or swollen, take the reading from the clean section of the body, not from the scaled end.

Only the heater. The order covers the heating cartridge itself — pot body, thermostat and glue sensor stay on the machine, so nothing else has to be removed to replace it.

Yes. Customisation is supported: send the diameter and the length you need and the cartridge is quoted to that size instead of the stock 12.5 x 205 mm.

No wattage is published for this listing, which quotes the part by number and by its two dimensions. The rating printed on the cartridge you are replacing is the value to send with the inquiry, and the quotation is matched to it.

Send the part number and the quantity. Price is quoted per inquiry rather than printed on the page, because it is given against the exact part number — 4-008-41-0227 or 4008410227 — and the size you confirm.

Yes. The same supply line carries various woodworking machine parts, so the rest of a pot or machine rebuild can travel in one inquiry instead of several suppliers.