4060180081 Chain Pad For Homag Edgebander 126x69x47mm Track Pads For Homag

Replacing worn track pads on a Homag edgebander? The 4060180081 chain pad is the conveyor track block that carries each panel past gluing and trimming. It measures 126 x 69 x 47 mm — 126 mm long, 69 mm wide, 47 mm high — and is moulded in PA 6 nylon specified at 55 Shore. The same pad is listed as Homag part number 4-060-18-0081. One worn block is swapped in place, so the conveyor chain stays on the machine and stays tensioned.

Three things stop an edgebander: a pad worn below its working height, a pad cracked at the mounting face, and a replacement ordered under the wrong part number. On a Homag edgebander the panel rides on pads fixed to the conveyor chain, so a pad that has lost height drops the board at the finishing station.

The 4060180081 is that pad. It is a single conveyor track pad for Homag edgebanders, catalogued under Homag part number 4-060-18-0081 as well as 4060180081. Each block measures 126 mm long, 69 mm wide and 47 mm high — length along the chain, width across the link, height above it. Get any one of the three wrong and the pad either will not seat or sets the panel at the wrong level.

It is moulded in PA 6 nylon, specified as 55SHORE PA 6 RO.KETTE LA.19 with 55 Shore recorded next to the size. That hardness figure is what the part is re-ordered by, so a new block can be checked against the worn one with a durometer.

Origin is China; the part is classed as a woodworking spare part. As a wear item it is ordered by part number and size, not by machine serial. Price is quoted on request.

Eight checks to run against the block already on your chain before you order.

• Two part numbers, one pad — the block is catalogued as 4-060-18-0081 and as 4060180081, so either number finds the same item.
• 126 x 69 x 47 mm — 126 mm long, 69 mm wide, 47 mm high, read as length, width and height on the block.
• PA 6 nylon body — moulded polyamide specified as 55SHORE PA 6 RO.KETTE LA.19, with the 55 Shore hardness recorded alongside the size.
• Conveyor chain position — the pad mounts on the conveyor chain of a Homag edgebander and carries the panel through the feed; it is not a fence-side guide.
• One support height per pad — every block holds the panel 47 mm above the chain link, so a worn one shows up as the pad that no longer matches its neighbours.
• Wear part, bought as one pad — a single part number covers a single pad, so one worn block is replaced without buying a chain assembly.
• Measured, not guessed — both the size and the 55 Shore figure are on the product record, so a repeat order can be checked with a caliper and a durometer.
• Origin and class — produced in China and classed as a woodworking spare part, which is the category most spare-parts desks file it under.

A worn pad leaves two choices: keep running and sort the scrap edge later, or pull the chain to change one block. The 4060180081 is the third option — change the block in place.

• Swap the block, leave the chain on. Because the pad is a separate chain part, one worn block is changed in place: nothing is stripped and nothing is re-tensioned.
• One height across the conveyor. With every pad at 47 mm, the panel is supported at the same level on each link, so the board does not ride up or drop.
• Numbers you can quote and measure. 126 x 69 x 47 mm and 55 Shore PA 6 are both on the record, so a new pad is checked against the old one before it goes on the chain.
• No variant list to work through. One part number, 4060180081, covers the pad, so the order is placed from the block in your hand, not from a machine serial.
• A wear item priced per order. Price is quoted against the quantity you need, so a small top-up and a full-chain order are quoted on the same part number.
• Built to the machine family. The pad is made for Homag edgebander conveyor chains, so the fit is to that chain rather than a block trimmed to size on site.

Yes, if the pad on your chain measures 126 x 69 x 47 mm. The block is made for Homag edgebanding machines and fits their conveyor track chain; measure the worn pad you are replacing before ordering, because the size decides the fit.

126 mm long, 69 mm wide and 47 mm high. On the block that reads as length along the chain, width across the chain link and height above it, and all three are quoted on the product record as 126 x 69 x 47 mm.

PA 6 nylon. The material is specified as 55SHORE PA 6 RO.KETTE LA.19, so the hardness is recorded as 55 Shore and the base polymer as polyamide 6.

Yes — one pad, two ways of writing the Homag number. The catalogue lists the block as 4-060-18-0081 or 4060180081, so either number reaches the same 126 x 69 x 47 mm pad.

On the conveyor track chain. The block is fixed to the chain and the panel rides on it as it is carried through the edgebander, which is why a pad that has lost height changes how the board sits.

Measure it against the new figure: 47 mm high and 55 Shore. A block that is under 47 mm, or visibly flattened on its contact face, is the one to change at the next chain check.

Yes. One part number covers one pad, so the block can be ordered on its own; count the pads on your chain to get the quantity for a full change.

Price is quoted on request — no list price is published for this part. Send the part number 4060180081 (or 4-060-18-0081) and the quantity, and the price is quoted against that.