KDT Edgebanding Machine Glue Pot Spare Part / KDT Edgebander Glue Stopper

Need the glue stopper back in the pot of a KDT edge bander without buying a gluing unit? Item 45114970 is that steel part. It seats in the glue pot casting, clamps the stopper blade at the outlet and is supplied in L & R — left-hand and right-hand, one per side of the pot. Steel body, bolt flange with a curved alignment slot, 1 clamp bolt on top, 1 knurled screw at the side for the guide plate. Accessories are available. Fits KDT edgebanders. Price on request.

On a KDT edge bander the glue bead is set by a few steel parts at the pot, and the glue stopper is one of them. Three things go wrong on a working bander: the stopper is ordered from a photo and arrives in the wrong hand, so it will not close the outlet; a worn blade stays in and the bead runs onto the panel edge; and once the glue line is bad, the whole gluing unit is quoted instead of the one part that failed.

Item 45114970 is the part for that third case: the glue pot spare part and glue stopper listed for KDT edgebanding machines, a steel body that seats in the pot casting and clamps the stopper plate at the outlet. It comes in L & R — left-hand and right-hand, 1 per side of the pot.

The body is a machined steel block on a base flange with bolt holes and a curved slot, so it is turned into line on the pot before the flange is tightened. A clamp bar on top, drawn down by a hex bolt, pinches the blade; a set screw beside it holds the setting. A knurled screw at the side locks the guide plate that leads the band past the outlet.

Accessories are available. Fits KDT edgebanders; price on request.

What the part is, in the terms a fitter asks for:

• Steel body — body, clamp bar and flange are steel, the material listed for item 45114970.
• Two handings, L & R — left and right, 1 per side of the pot, so the hand is quoted instead of guessed.
• Clamp bar on a hex bolt — the blade is pinched by 1 hex bolt, so a change needs one spanner.
• Set screw beside the bolt — it holds what the clamp bolt set, so the blade does not creep.
• Knurled side screw — the guide plate is locked by a knurled screw and set by hand, with no tool.
• Flange with a curved slot — bolt holes plus an arc slot, so the body is rotated into line before it is tightened down.
• Face plate on 2 screws — the wear plate is held by 2 cross-head screws, the first thing to check when a bead creeps.
• Seats in the pot casting — the body drops into the machined seat and the flange holds it, as the assembly photo shows.
• Accessories available — screws, guide plate and clamp parts come on their own, so 1 worn screw is not a new body.

When the glue line goes bad, the choice is a gluing unit or the steel part that failed. This is that part, and this is what the buyer gets.

• Change the stopper, not the gluing unit. Pot casting, roller and heating side stay put; the work is 1 flange off, 1 on.
• The handing is stated before you pay. L & R are separate, so the order says left or right, not "same as photo".
• One spanner for the blade. Pinched by a single hex bolt under the clamp bar, so a fitter swaps it at the machine.
• Alignment that repeats. The curved slot lets the body be turned into line and locked, so the next blade lands in the same place.
• Adjustment at the part, by hand. The knurled screw sets the guide plate, so a small drift needs no service visit.
• Steel where the clamp loads. The faces that carry the bolt load are machined steel, not plated sheet.
• Accessories on the same line. Screws, guide plate and clamp parts arrive with the body, not as a second shipment.
• A part number to quote. 45114970 plus the hand and quantity is enough for a price; no drawing for a repeat order.

Yes, if your machine carries this pot-mounted stopper. The part is listed for KDT edge banding machines, where it seats in the glue pot casting and clamps the stopper blade at the outlet. Quote the machine model when ordering and the match is checked before the order is confirmed.

Both exist, and they are not interchangeable — L & R are separate handings. Look at which side of the pot the failed part sits on and order that hand; if the machine has two pots, check each side before ordering.

Steel. Body, clamp bar and mounting flange are steel, which is the material listed for item 45114970, and the faces that carry the clamp bolt are machined.

No. This is a spare part in its own right and replaces the stopper assembly in the pot, so the pot casting, the roller and the heating side stay on the machine.

With one spanner. Release the hex bolt on the clamp bar, lift the bar, swap the blade, then tighten the bolt and lock the setting with the set screw beside it.

By hand, at two points. Turn the body on the curved slot until it lines up with the roller, tighten the flange, then set the guide plate with the knurled side screw and hold the clamp setting with the set screw.

Yes. Accessories are available, so the guide plate, the clamp parts and the screws can be ordered separately from the body.

Send item no. 45114970, the hand (L or R) and the quantity, and you get a quotation. Price is quoted on request rather than printed on the page.