Nanxing Glue Pot Shaft L409mm Glue Pot Roller For Nanxing Edgebanding Machines

Need a glue pot shaft that matches the Nanxing edgebander already in your shop? This assembly is listed as the Nanxing 60C glue pot shaft, also sold as the Nanxing glue pot roller, at 409 mm overall length - the one number to measure on the old part before ordering. It sits in the glue pot of the Nanxing NB series, where the knurled body holds glue through the run. One shaft, 1 measurement, 1 line item. Origin: China. Glue pot available separately.

Three things go wrong around a gluing station: the glue bead stops running even, the shaft that carries it wears at the knurled working face, and one worn part looks like it means replacing the entire glue pot. Most shops then run the old shaft until panel edges start showing it, and lose the setting they had.

This is the edge banding machine glue pot shaft assembly for Nanxing edgebanders: 1 assembly, 409 mm long, listed for the Nanxing NB series and named on the listing as the Nanxing 60C glue shaft. The knurled body, the ribbed hub, the flange and the threaded end with its hex nut come on the same part, so the shaft that the glue pot drives is exchanged in one step instead of being rebuilt piece by piece on the bench.

The same listing family carries 4 more glue pot lines - heating panels, heating tube, glue pot and the edgebanding gluing system - so parts that usually wear together can be quoted together.

Ordering is a measuring job rather than a guess: check the old shaft at 409 mm overall and quote the machine model. Origin: China. Price on request.

What arrives on this part, as numbers you can check against the machine on your floor.

• 409 mm overall length - the first number to measure on the old shaft; it spans the knurled body, the flange and the threaded end.
• 1 assembly, 1 line item - knurled body, ribbed hub, flange and threaded end arrive together, so nothing gets rebuilt on the bench.
• Listed for the Nanxing NB series - model reference NANXING NB, shaft named NANXING 60C; match both to the machine plate.
• Diamond knurl on the working face - the knurl runs the full working length rather than a plain ground face, and that texture is what holds glue through a run.
• Threaded end with hex nut - thread and fastener come on the assembly, so the shaft locks the way the old one did.
• Glue pot available - the pot is listed separately as available, so shaft and pot can leave in 1 shipment.
• 4 related glue pot lines - heating panels, heating tube, glue pot and the gluing system, so a full gluing-station refresh is 1 quote.
• Origin China - 1 stated origin, so the country on the order is the country on the paperwork.
• Heavy-duty box with cushioning - labelled with customer name, address and phone number, 1 box per order line.

At the gluing station there are usually two options: keep running a shaft that has already worn, or buy the whole pot. This part gives you a third.

• Replace the shaft, not the pot. A 409 mm assembly is 1 line item that goes straight into the existing glue pot, so the rest of the gluing station stays where it is.
• One measurement decides the order. Match 409 mm overall plus the model (NB / 60C) and there is no second guess on length - which is the fault that usually sends a spare part back.
• Glue feed stays even across the panel. The diamond knurl spans the full working length, so the glue is picked up over 1 continuous face instead of a patchy one.
• Downtime counted in one swap. The hub, flange and nut come on the shaft, so the machine is down for 1 part change and not for a rebuild.
• The gluing station gets priced once. 4 accessory lines share this listing family, so shaft, heater and pot are quoted together and shipped together.
• Nothing on the page has to be taken on trust. Every claim here is a number from the listing or a feature visible in the photos: 409 mm, NB, 60C, 4 accessory lines.

The Nanxing NB series. The listing carries the model reference NANXING NB and names the part NANXING 60C glue shaft, so check both against the plate on your machine before you commit the order.

409 mm overall. Measure your old part from end to end, including the threaded end and the flange, and compare that single figure before ordering.

Both names describe the same part. The listing titles it a glue pot shaft and also calls it a glue pot roller, because the knurled body is the surface that carries glue in the pot.

No. This line is the shaft assembly on its own; the glue pot is listed separately as available, so order it as its own line if the pot is also worn.

Yes. Four lines sit in the same family: heating panels, heating tube, glue pot and the edgebanding gluing system, and they can be quoted on one order.

Send two things: the machine model (NB series, 60C shaft) and a measurement of the old shaft at 409 mm. If either figure differs, the part is not the right one.

Price is on request, and MOQ and lead time are confirmed in the quote rather than fixed on this page. Send the model and the quantity you need and the figures come back with the quotation.

In a heavy-duty box with cushioning. The box is labelled with the customer name, address and phone number, and the shipment is given a tracking number so it can be followed online.