Bracket Roller For HOLD Edgebander - HOLD Woodworking Edgebanding Machine Spares

Ordering the wrong hold-down roller is the usual reason an edgebander stays down for a week. This one is specified by three numbers: 22.5 mm roller diameter, 25 mm roller height and a 5 mm rod diameter, in white plastic, part number 44254435, listed for HOLD edgebanding machines. Match those three sizes against the bracket you are taking off and the part drops in with no adapter, no re-machining and no shimming. It is a spare-parts line item, so it can be bought on its own instead of as part of a whole hold-down assembly. Price is quoted per order.

An edgebander usually stops for something small. A hold-down bracket roller seizes, the panel starts lifting off the fence, the glue line wanders, and the shift waits on a part that costs less than the coffee run. The two usual answers are both wrong: buy a complete hold-down sub-assembly, or measure roughly and hope the rod diameter is close enough.

This is the single part instead. A white plastic bracket wheel for HOLD edgebanding machines, item 44254435, with a 22.5 mm roller diameter, a 25 mm roller height and a 5 mm rod diameter - the three numbers that let your storeman check the old bracket before anything ships.

The roller runs on the panel face, so its condition sets how the board tracks. A wheel that is worn flat, or one that no longer spins, lets the panel ride up and the edge sits proud at the joint. Replacing the bracket as one unit keeps the roller axis square to the fence, which is what a shimmed loose wheel never does.

Treat it as a consumable. Unbolt the old bracket, fit the new one, reset the hold-down pressure, and the line is back in the same shift. The same part is searched as a bracket roller, a supporting roller or a bracket wheel, so order it under whichever name your manual uses.

Seven details decide whether the bracket drops straight onto your machine or comes back as a return.

• 22.5 mm roller diameter - matches the original HOLD hold-down wheel, so panel height setting stays where your operator left it.
• 25 mm roller height - full contact width across the hold-down zone, not a narrowed generic wheel that only touches the edge of the board.
• 5 mm rod diameter - the pin size the bracket bore is cut for; measure the old rod before you order, because this is the size most often guessed wrong.
• Plastic body in white - non-marking on white melamine and light veneer, and light enough that the bracket adds no load to the fence.
• Bracket and wheel as one unit - no separate axle or bushing to lose on the floor during fitting.
• Listed for HOLD edgebanders - sold against HOLD machines rather than adapted from another brand's bracket, so the fixing holes line up.
• Carried as a spare-parts item - orderable on its own, in the quantity you need, instead of being locked inside a machine sub-assembly.
• Part of a wider spares range - CNC vacuum pods, Homag and Weeke parts, valve inserts, locating rings and gaskets can ride on the same purchase order.

The choice is not between two rollers. It is between a panel that tracks through the machine and a shift that stops while somebody works out what to order.

• Match on a number, not on an eye. Part 44254435 plus 22.5 x 25 mm and a 5 mm rod gives your storeman three checks before the order leaves, which is how wrong-part returns get avoided.
• Keep one on the shelf. At this size the bracket is worth holding two of; a seized roller becomes a ten-minute swap, not three days of downtime.
• Protect the panel face. A white plastic wheel leaves no grey track on white melamine or light oak veneer - the mark a steel roller leaves behind.
• Keep the glue line straight. A roller that still runs square holds the board against the fence, so the edge sits flush and the end-trimming unit has less to take off.
• One supplier for the rest of the list. Beyond this bracket we supply CNC vacuum accessories, Homag and Weeke spare parts, Schmalz vacuum pods, cups and rubber pads for Biesse and SCM machines, plus valve inserts, locating rings and gaskets.
• Order by the manual's own name. Bracket roller, supporting roller and bracket wheel all point to 44254435, so an old stores list still resolves to the same item.

Check the three sizes before ordering - that is the only reliable answer. The roller measures 22.5 mm across, 25 mm high and runs on a 5 mm rod; if the bracket you are replacing matches all three and your manual lists HOLD, it is the right part.

The bracket with its roller, as one unit. You do not need to order a wheel, an axle and a bracket separately, and there is no bushing to press in afterwards.

No - order by part number and quantity, not by side. 44254435 is listed as one item, so count how many hold-down positions have failed on your machine and order that number.

Plastic, in white. That matters on light board: a plastic wheel does not leave the grey contact track a steel roller can leave on white melamine or pale veneer.

Replace it when the panel starts lifting off the fence or the edge sits proud at the joint. A wheel that still spins freely but has worn flat no longer holds the board down, even though it looks fine in place.

It is a bolt-on job: unbolt the old bracket, fit the new one, then reset the hold-down pressure. No machining, no adapter plate and no alignment fixture are involved - the roller axis comes square with the bracket.

Only if the sizes and the fixing both match. It is listed for HOLD machines, and other brands use different bracket castings and rod sizes, so measure the old bracket instead of assuming the brand is close enough.

Yes. Alongside this bracket we supply CNC vacuum accessories, Homag and Weeke spare parts, Schmalz vacuum pods and suction plates, rubber pads and cups for Homag, Weeke, Biesse and SCM machines, and small items such as valve inserts, locating rings and gaskets.