Edgebander Glue Pot Gluing Unit Edgebanding Glue Tank For HOMAG Machine

Need a glue pot for a HOMAG or Brandt edge bander without waiting on the machine builder's parts desk? This is the complete gluing unit — universal type with a PT100 temperature element, listed for HOMAG Brandt high speed automatic edge banding machines, article 41556249. The photos show the assembly as supplied: brass reservoir, knurled glue roller in a doctor blade frame, blue perforated heat guard, two ball knob levers and a cable with plug connector. MOQ 1 pc, delivery 1–7 working days, price on quotation.

A HOMAG or Brandt line loses an hour in three familiar ways: the pot clogs and the band runs down dry, adhesive creeps past the pot flange, and a replacement pot with the wrong sensing element reports a temperature the control cannot act on. All three end at the same part — the gluing unit — so the repair is a unit swap, not a bench rebuild.

This is the glue pot and gluing unit for HOMAG Brandt high speed automatic edge banding machines, the assembly that melts granulate and lays the film on the band edge. It is the universal type with a PT100 temperature element, sold as edge banding machine spare parts under article 41556249.

The photos show what the part is: black cast housing, brass glue reservoir, knurled glue roller held in a doctor blade frame, blue perforated heat guard, 2 ball knob levers, and 1 cable ending in a grey multi pin plug. None of those is a separate extra, which is why one part number covers the whole failure.

Colour is as the picture shows. Minimum order is 1 pc, delivery is 1–7 working days, and OEM/ODM is acceptable. Packing is standard export carton, price comes by quotation, and payment terms are agreed per order. When a pot change stops the line, this is the part that ends the wait.

What the sheet and the three photos establish:

• Universal type, PT100 element — the sensing element is a PT100, the type the HOMAG Brandt control reads, so one spare fits more than one build.
• Sold as the whole unit — reservoir, glue roller, doctor blade frame, heat guard, levers and cable come on one assembly: a failure is one swap, not a build.
• Knurled roller in a blade frame — the cross hatch surface holds adhesive across the full band width, and the frame sets that film in one pass.
• Blue perforated guard — a punched grid covers the hot side and carries the burn pictogram, so the heat shows before a hand goes near.
• Two ball knob levers — 2 levers set roller pressure and blade position by hand, without a spanner.
• Cable with plug connector — the lead ends in a grey multi pin plug, so the unit meets the machine socket instead of being terminated wire by wire.
• Brass reservoir, black housing — the adhesive block is brass, the body behind it black cast: heat on one side, knocks on the other.
• Listed as no damage on panels — the sheet names it that way, and glue lines on the panel face are exactly what a tired roller or frame causes.
• OEM/ODM accepted — non standard builds and house branded parts are quoted from 1 pc.

The alternative is a bench rebuild, or a pot that keeps scorching adhesive until the next band runs down dry:

• A stoppage counted in days, not months. Delivery is 1–7 working days from order, so a pot failure does not become a long wait on a machine builder's parts desk.
• One article number for a mixed floor. The universal type PT100 build serves HOMAG Brandt high speed automatic banders, so the shelf carries 41556249 instead of a different number per machine year.
• The wiring stays on the machine. A cable with a plug connector means unplug, lift out, drop in — no terminal by terminal rewire inside the cabinet.
• Glue lines stop reaching the panel face. A roller and frame that still meter a full width film is the point of the no damage on panels line, and the difference between banded board and rework.
• Order the quantity the job needs. MOQ of 1 pc means a single machine can be put back in service without a pallet of spares on the shelf.
• A non standard build is not a dead end. OEM/ODM is acceptable, so a machine variant outside the standard schedule does not have to be turned away.

It is listed for HOMAG Brandt high speed automatic edge banding machines, so yes if your machine is in that family. It is the universal type with a PT100 element, and the fitment line to check before ordering is the pot mounting and the plug on your existing unit.

The whole unit. The photos show the brass reservoir together with the knurled glue roller, doctor blade frame, perforated heat guard, 2 ball knob levers and the cable with plug, so it replaces the assembly rather than one casting.

A PT100 element — that is what the universal type designation on the sheet refers to. It is the sensing standard the HOMAG Brandt control reads, so the pot reports on the same channel as the one it replaces.

No. The lead ends in a grey multi pin plug, so the connection is made at the machine socket. Nothing has to be terminated wire by wire, and no cabinet door has to come off for the adhesive side of the job.

The version shown in the pictures: blue perforated heat guard, black cast housing, brass reservoir, 2 ball knob levers and a grey plug. Colour is as the picture shows, so the photo set is the specification.

Yes — MOQ is 1 pc. Price is quotation on request and payment terms are to be negotiated, so send the machine model and the quantity and the quote comes back against that.

1–7 working days from order, packed in a standard export carton. Origin is China. Confirm the destination with the order so the carton and the paperwork match the route.

Yes. OEM/ODM is acceptable, so a non standard build or a house branded part can be quoted from a drawing or a sample. Start from 1 pc and send the detail with the enquiry.