Edgebanding Bracket Roller 25x4x26 Edgebander Plastic Conveyor Roller

Need to get a CNC edge bander running again without replacing the whole bracket assembly? This 25*4*26 mm black nylon bracket roller is the replacement guide roller that presses and steers the band onto the panel edge. It is moulded in one piece from solid nylon, black through the body, so there is no rubber skin to soften next to the glue pot. Size 25*4*26 mm, fits woodworking CNC edge banding machines, dispatched from Guangdong, China. Other sizes are quoted on request.

An edge bander that stops feeding part way through a panel usually traces back to one small part. Three headaches repeat: a flattened roller that lets the panel drift, a rubber roller that softens against hot glue and marks the edge, and a replacement that arrives with the wrong centre. The 25*4*26 mm bracket roller is made to close all three at once.

This is the bracket roller that sits in the edge banding station of a CNC edge bander, holding the band against the panel edge as the workpiece travels past. It is moulded in nylon — solid, black, one piece — to the 25*4*26 mm envelope used on CNC edge banding machines, so it takes the position the original roller came out of on the same bracket.

Nylon is the reason this part holds where rubber gives up. A rubber wheel softens near the glue pot, swells, then runs out of round; nylon keeps its diameter and its black colour, and it leaves no soft skin behind on pale melamine or white PVC edge. There is no skin to peel at 25*4*26 mm.

One roller, one fitment, no special tooling. It is supplied for CNC edge banding machines and listed under woodworking machinery spare parts, delivered from Guangdong, China. Other sizes are available on request, including 28*3*26 mm and 25*6*26 mm rollers from the same family.

Eight points worth checking before you order a replacement bracket roller, all of them read against the 25*4*26 mm part.

• Moulded nylon body — one solid black nylon roller, no rubber cover to soften, swell or tear at 25*4*26 mm.
• 25*4*26 mm envelope — the three dimensions are quoted in millimetres in the order printed on the original part, so you can measure the old roller before ordering.
• Bracket station fitment — sits at the bracket roller position on CNC edge banding machines in woodworking plants, 1 part replacing the worn one.
• Black through the body — the colour comes from the nylon itself, so the roller is still black at 25*4*26 mm after the running face has polished in.
• Runs beside the glue line — nylon holds its shape in the 25*4*26 mm body where a rubber wheel goes soft and takes a set.
• Even side load — a straight cylindrical face across the 25*4*26 mm body spreads the pressure that keeps the band square to the panel edge.
• Single dispatch point — packed as 1 roller and shipped from Guangdong, China, so nothing else has to be ordered to finish the job.
• Size options on request — 28*3*26 mm and 25*6*26 mm versions of the same bracket roller family are quoted from the same source.

Buying an edge bander roller normally comes down to a two-way choice: wait for a dealer part, or run a rubber wheel that marks the panel. At 25*4*26 mm neither is necessary.

• You stop losing panels, not just hours. A flat roller lets the band ride off the edge; a 25*4*26 mm nylon roller keeps the band square, so the rework pile stays small.
• Glue heat stops being a wear item. Rubber goes soft beside the glue pot; nylon holds its diameter at 25*4*26 mm, so the roller is changed when it wears out, not when the shift warms up.
• Clean edges on white and pale decor. A solid black nylon body has no soft skin to smear across the panel, so the edge leaves the station clean the first time.
• One part number covers the order. 25*4*26 mm, nylon, black — three lines and the enquiry is complete, with no hidden fitment to negotiate.
• The delivery address never changes. Every roller ships from Guangdong, China, so a reorder goes to the same place as the first one.
• Room to cover the rest of the line. When 25*4*26 mm is not the size on a second machine, 28*3*26 mm and 25*6*26 mm rollers are quoted from the same family.

Yes, if the roller on your bracket measures 25*4*26 mm. It is made for the bracket roller position on woodworking CNC edge banding machines, and it fits the existing bracket without any mount rework.

Nylon. The body is solid black nylon moulded in one piece at 25*4*26 mm, so there is no rubber cover that can soften, swell or tear away from the core.

They are the three dimensions in millimetres, quoted in the same order as the original part number. Compare all three against your old roller before ordering, rather than assuming which one is the bore.

Yes. Other sizes are quoted on request, including the 28*3*26 mm and 25*6*26 mm bracket rollers from the same family, so tell us the size on your machine and we will quote that version.

Ask us before ordering — no fixed minimum is published for this roller. Send the size, 25*4*26 mm, and the quantity you need, and the quantity is confirmed with the quote.

Guangdong, China. That is the delivery place for this part, and it is the same dispatch point for the 28*3*26 mm and 25*6*26 mm sizes.

No soft coating is present to transfer. The colour is in the black nylon itself rather than on a coated skin, so the running face does not leave a rubber smear on pale melamine or white PVC edge.

Because size and quantity drive it. Price for the 25*4*26 mm roller is quoted on enquiry, so send the size you need and the quantity and the price comes back with it.