54x8x40mm Pressure Wheel Press Roller For Qingdao Woodworking Edgebander

Replacing a glazed press wheel usually turns into ordering a whole press unit, because nobody wrote down which wheel was on the machine. The PSW057 is identified by three caliper readings: φ54 mm outside diameter, φ8 mm shaft, 40 mm face width. Grey rubber, gear surface with straight tracking, bearing fitted. It presses solid wood, veneer and laminate banding against the panel edge on the same spindle height, so no press setting is re-tuned.

Three faults show up before a press wheel is ordered: banding lifts at the panel edge because the rubber face has glazed, a wheel arrives that does not fit because it was bought by machine brand instead of size, and a whole press assembly is scrapped for one worn tyre.

This is the gear pressure rubber wheel for the press section of a woodworking edge banding machine, listed for Qingdao edgebanders. Outside diameter φ54 mm, shaft φ8 mm, face width 40 mm, colour grey, bearing fitted. The φ8 mm shaft seats on the existing spindle and the φ54 mm diameter holds the contact height already set.

The surface is a gear roller with straight tracking, so the tooth pattern drives the banding forward in a straight line instead of relying on rubber friction. The rubber body lets the face sit on solid wood, veneer and laminate edges instead of sliding across them. A smooth roller is also available.

Wheels are not interchangeable between edgebander brands. The range covers gear rollers with or without bearing, smooth rollers with or without countersink, and gear rollers with or without countersink; the two tooth patterns are straight tracking and angle tracking. Packing is a carton.

Three caliper readings and one face type decide whether this wheel goes straight onto your press unit.

• Measured size, not model year — φ54 mm outside diameter, φ8 mm shaft, 40 mm face width, read off the old wheel.
• Gear face with straight tracking — the teeth run the banding along a straight line; angle tracking is the other tooth pattern made.
• Rubber contact face — presses solid wood, veneer and laminate edges instead of skating over a polished face.
• Bearing fitted — the wheel comes as a gear pressure rubber wheel with bearing, so the φ8 mm shaft is a straight fit.
• 40 mm face width — one pass covers the banding width with the pressure spread along the glue line.
• Smooth version also available — for units that only press the tape down, in the same edgebander press family.
• Countersink on request — smooth and gear rollers are made both with and without a countersunk centre.
• Grey compound — colour matches the product photo, so incoming stock is checked at a glance.
• Carton packed — a spare set travels as a carton, no crate and no pallet.
• Brandt consumables alongside — track pads and high temperature heat-resistant rollers for Brandt edgebanders come from the same supply.

A press wheel is usually special-ordered with a month of waiting, or guessed from a photo. What changes when it is bought by measurement:

• The edge stops lifting. A glazed tyre lets the banding spring off the glue line; the 40 mm rubber face holds pressure across the full width until the glue grabs.
• No wrong-order loop. Ordering by φ54 × φ8 × 40 mm removes the brand guessing that sends a wrong bore back across an ocean.
• One wheel, not one assembly. The press unit stays on the machine; only the φ8 mm bore wheel is changed, so you buy a wheel, not a shaft.
• Press height unchanged. Same φ54 mm diameter as the old wheel, so the pressure setting survives the swap.
• Straight tracking keeps the banding on line. The gear face pulls the tape forward in a straight line, so a feed that wandered no longer needs a hand.
• Three edge materials, one stock item. Solid wood, veneer and laminate run on one rubber face, so mixed orders do not need three wheels on the shelf.
• A wear part worth keeping. Two wheels per press unit is a practical stock level; a stopped edgebander costs more per hour than the spare.
• Smooth or gear, same reference. A second press unit needing a smooth roller is quoted under PSW057, keeping sourcing in one place.

Yes, if three readings on the old wheel match: φ54 mm outside diameter, φ8 mm shaft, 40 mm width. Edgebander brands use different wheel shapes, so the size identifies the part rather than the machine name — send the three readings and the face type if you want it confirmed first.

It is a gear roller with straight tracking. The teeth drive the banding along a straight line; angle tracking is the other tooth pattern available, and a smooth roller is also made for units that only press the tape down.

Yes. It is supplied as a gear pressure rubber wheel with bearing, so the φ8 mm shaft is a straight fit and no separate bearing has to be pressed in.

The rubber face has gone hard or glossy, and the banding starts lifting at the panel edge. Once the surface has glazed it will not grip again, so turning up the press pressure only deforms the panel.

Solid wood, veneer and laminate. The rubber face conforms to the banding instead of pressing it on a hard ring, which is what lets one wheel cover all three materials.

Straight tracking keeps the toothed face running parallel to the banding path; angle tracking is the second tooth pattern in the range. Look at the old wheel: if the teeth are cut straight across the face, this version matches.

Then order the countersunk version. Smooth rollers and gear rollers are both made with or without a countersunk centre, and with or without a bearing, so the centre pattern has to be stated with the size.

It is packed in a carton, and the price is quoted per order. Send the quantity, the face type and the destination, and the figure comes back with the packing confirmed.