2-212-10-0200 Rubber Pressure Roller For Homag Edgebander - Press Wheel 70x20 Con. x25mm

Need to replace a worn press wheel on a Homag or BRANDT edgebander? The PSW050 rubber pressure roller mounts on the existing shaft: φ70 mm outer diameter, φ20 mm bore, 25 mm wide, grey rubber, convex face, gear surface with straight tracking, supplied without bearing and without countersink. Part numbers 2-212-10-0200, 2212100200 and PSW050 all identify this one roller. The crowned face loads the full 25 mm width of the band, so the tape is pressed from shoulder to shoulder instead of only down the middle.

A banding line that starts lifting along the edge, while the glue setting has not changed, usually has one cause: the press wheel. The rubber goes hard, the face loses its crown, and the tape is no longer pressed down across its full width. The effect shows up further down the line, as rework on the finished edge. The PSW050 is the replacement wheel for Homag and BRANDT edgebanders.

It is a grey rubber press wheel: φ70 mm outer diameter, φ20 mm bore, 25 mm face, supplied without bearing so it mounts straight on the machine shaft. The face is convex, crowned over the 25 mm width and falling away towards both shoulders, which spreads load across the whole band instead of onto its centre line.

The running surface is a gear roller with straight tracking: straight knurls parallel to the axis, gripping the band and holding it straight past the glue unit. It is without countersink and without groove, so the bore is plain and the shoulder runs the full width. 2-212-10-0200, 2212100200 and PSW050 all refer to this roller, and a smooth roller in the same size is available where the unit runs plain wheels.

Every line below comes from the part itself: size, profile and surface finish are the three things that decide whether a press wheel fits and whether the band tracks straight.

• Direct replacement size — φ70 mm outer diameter, φ20 mm bore and 25 mm across the face, the size a Homag or BRANDT pressure unit takes.
• Convex face — crowned over the 25 mm width, so load reaches both shoulders of the band instead of sitting on the centre line.
• Gear surface with straight tracking — straight knurls parallel to the axis hold the band on a straight line past the glue unit.
• Without bearing — plain φ20 mm bore, no sealed bearing to seize; the roller turns on the machine shaft and is the only wear item.
• Without countersink, without groove — plain bore and a full 25 mm shoulder, so it is one item to stock, not a wheel plus a flange.
• Grey rubber body — soft enough to press a band onto a finished panel face without marking it.
• One size, two machine brands — the same 70 / 20 / 25 mm roller is listed for Homag and BRANDT edgebanders, so one stock line covers both.
• Smooth version available — where the unit runs plain pressure wheels, the smooth roller comes from the same source.

Keeping a hardened wheel in service, or waiting on a factory delivery while the line stands still, are the two options a banding shop usually has. This roller is the third one: a 70 / 20 / 25 mm part that is ordered from stock and fitted by the operator.

• The edge stays down where it matters. The convex crown loads the full 25 mm width of the tape, including the two shoulders where lifting starts.
• Three references, one roller. 2-212-10-0200, 2212100200 and PSW050 resolve to the same 70 / 20 / 25 mm convex wheel, so a wheel ordered from any of those numbers fits the shaft.
• One wear part on the shaft, not two. With no bearing inside there is no sealed unit to seize; the φ20 mm bore runs on the shaft and the wheel is what gets replaced.
• A straight band makes a straight edge. Straight knurls keep the band on line into the trimming units, where a wandering band shows up as a stepped edge.
• One shelf line for two machine brands. Because the size serves Homag and BRANDT pressure units, a workshop running both brands stocks one wheel instead of two.
• Re-ordering without a drawing. 70 / 20 / 25 mm, convex, no countersink: three call-outs are enough to place the next order.

Yes, if your pressure unit takes a 70 / 20 / 25 mm wheel. φ70 mm outside, φ20 mm bore and 25 mm face is the size this roller is built to, and it is listed as a spare part for Homag and BRANDT edgebanders. Check the bore and width on the wheel you are removing before you order.

Yes. Three labels, one roller: 2-212-10-0200, 2212100200 and PSW050 all describe the same φ70 × φ20 × 25 mm grey convex gear roller without bearing.

No. It is supplied without bearing, with a plain φ20 mm bore that mounts directly on the machine shaft. There is no sealed bearing inside to replace and no separate bearing to order.

It spreads pressure across the full width of the band. The face is crowned over the 25 mm width and falls away towards both shoulders, so the tape is loaded at its edges as well as at its centre — and the edges are where lifting starts.

It is a rubber roller with straight knurls, cut parallel to the roller axis. The knurls grip the band and keep it running in a straight line as it is pressed onto the panel edge, instead of letting it drift to one side.

Only if the wheel you are replacing has a counterbored or grooved bore. This part is without countersink and without groove, with a plain bore and a full-width shoulder over the 25 mm face.

Yes. A smooth roller is available where the pressure unit runs plain wheels rather than gear rollers. Size, convex face and the no-bearing bore stay the same; only the running surface changes.

Price, MOQ and lead time are quoted per order, because they depend on quantity and destination. Send the number of wheels you need plus your machine model, and the quotation is issued against those figures.