φ65xφ8x14mm Rubber Pressure Roller Wheels For NANXING Edge Banding Machine

Need to get a NANXING edge banding machine back to a flat, closed glue line? Start with the three numbers that decide the fit: φ65 mm outside diameter, φ8 mm bore and 14 mm face width. The PSW023 is a white rubber pressure roller wheel with an angle tracking gear type, replacing the worn wheel on the pressure station without touching the roller position. It presses the panel against the conveyor chain pad, so banding in solid wood, PVC, melamine and veneer all gets pressed across the full face. Quotation on request.

A pressure wheel that has gone hard, glazed or out of round shows up in three places: banding lifts at the panel ends, a glue line opens along the top edge, and clean panels start coming out marked. A replacement that is 1 mm out on bore size will not sit on the shaft at all.

The PSW023 is the wheel that takes all four out of the day. It is the pressure roller on the edge banding station: φ65 mm outside diameter, φ8 mm bore and 14 mm face width, in white rubber, with an angle tracking gear type that presses the panel against the conveyor chain pad.

One wheel covers four banding materials: solid wood, PVC, melamine and veneer. The rubber face is the same for all four; what changes is the glue and the station temperature, not the wheel. The gear type is angle tracking; the other gear type in this range is straight tracking.

Fit is decided by three measurements, not by the machine model alone. Measure the old wheel across the outside diameter, the bore and the face width, compare with 65 / 8 / 14 mm, and the wheel mounts on the same pressure shaft at the same roller position. Smooth rollers and other sizes in this range are quoted to your measurement.

What three dimensions and one gear type decide — and what they leave to the rest of your machine:

• NANXING station fit — φ65 mm outside diameter, φ8 mm bore and 14 mm face: the three numbers that decide whether the wheel sits on the shaft.
• White rubber face — the full 14 mm face presses the banding; a face worn narrower leaves the top edge of the band unpressed.
• Angle tracking gear — the angle tracking type, one of 2 gear types in this range; the other is straight tracking.
• Chain pad partner — the wheel presses the workpiece against the conveyor chain pad, which makes the glue bond along the edge.
• 8 mm bore — slides onto the existing pressure shaft, with no adapter and no shaft change.
• Four banding materials — solid wood, PVC, melamine and veneer all run against the same rubber face.
• Smooth version available — the same range covers smooth rollers, so a station running a plain wheel can be matched.
• Other sizes quoted — if 65 / 8 / 14 mm is not your size, the size off the old wheel is enough to quote from.
• Consumable logic — 1 spare per station turns a glazed face into a swap, not a wait.
• Size differs by machine — pressure wheels vary in size and shape between edgebander makes, so measure the old wheel.

Two bad options, and where this wheel sits between them: order a guess and lose a shift, or keep running a glazed face and lose panels.

• Closed ends without rework. A worn 14 mm face lets the banding lift at the panel ends, and every lifted end is a rework; a fresh face puts pressure back across the full width.
• Right part on the first order. Diameter, bore and width are the only 3 numbers that decide fit, so measure the old wheel against 65 / 8 / 14 mm before ordering.
• Machine stays set up. The 8 mm bore matches the existing pressure shaft, so roller position and station pressure do not change when the wheel is swapped.
• One supplier for the station. Smooth rollers and the other sizes in the range come from the same place, so a second pressure station is not a second search.
• The gear type your station asks for. This range lists 2 gear types, straight tracking and angle tracking; PSW023 is the angle tracking one, so the station does not have to be changed over.
• A quote against three numbers. Send the machine model and the measured size, and the price is quoted against 65 / 8 / 14 mm rather than against a catalogue name.

Yes, if three numbers match. The wheel is φ65 mm outside diameter, φ8 mm bore and 14 mm face width; measure the old wheel, and if those three agree it mounts on the same pressure shaft. Send the machine model and the measurement if you want it checked before you order.

Outside diameter 65 mm, bore 8 mm, face width 14 mm. The bore is the hole the pressure shaft goes through; the face width is the part that touches the banding.

Geared. The spec lists a gear type of angle tracking, so this is the geared wheel; the smooth roller is a separate version in the same range and is also available.

That is the gear type name. This range lists 2 gear types — straight tracking and angle tracking — and PSW023 is the angle tracking one, so a station built for straight tracking is a different wheel.

Solid wood, PVC, melamine and veneer. The rubber face is the same for all four; the banding material changes the glue and the station temperature, not the wheel.

Three signs. The banding lifts at the panel ends, a glue line opens along the top edge, or the rubber face has gone hard and glossy — once it glazes it stops gripping, whatever the pressure setting says.

Yes. The smooth roller version is also available, and if 65 / 8 / 14 mm is not your size, send the measurement off the old wheel and the matching size is quoted from the same range.

Price is quotation on request. Send the machine model, the size measured off the old wheel (diameter x bore x width), the banding material you run and the quantity per station, and the quote is made against that measurement.