PSW021 62x16x24mm Press Roller Rubber Wheel For CEHISA CNC Edge Banding Machine

Need a direct replacement pressure roller for a CEHISA CNC edge banding machine? PSW021 is the white rubber press roller measuring 62 mm outside diameter, 16 mm bore and 24 mm face width. It mounts on the shaft already on the machine, presses the band across the full 24 mm face instead of a single line, and is specified for the heated glue area behind the pot. Same three numbers as the wheel in your machine, one part number for repeat orders.

An edge bander rarely loses its bond at the glue pot; it loses it where the band meets the pressure roller. Three things go wrong there: the white rubber wheel hardens and stops gripping, a substitute with the wrong bore sits off centre, and the right part has to be ordered and waited for.

It is a solid rubber pressure roller for CNC edge banding machines: 62 mm outside diameter, 16 mm bore and 24 mm face width, moulded in white and catalogued as PSW021. The 62 mm diameter meets the band, the 24 mm face spreads pressure across the full band height rather than one line, and the 16 mm bore mounts on the shaft already on the machine.

The compound is specified for the glue area, where the roller runs against warm band and a freshly glued edge, and specified as wear-resistant. White is deliberate: on a machine that also carries black bracket rollers, the press roller is the one a fitter picks out at arm's length.

PSW021 is listed for CEHISA CNC edge banding machines, and for any unit using the same 62 × 16 × 24 mm position. It runs against wood, plastic and laminate banding. Alternate sizes cover 48–70 mm outside diameter, 8–18 mm bore and 12–27 mm width; parts ship from Foshan, Guangdong, China.

Seven points you can measure against the wheel already on your machine.

• 62 mm contact diameter — the outer face that presses the band onto the panel edge, and the number a worn wheel is measured against.
• 16 mm bore — the mounting hole that puts the wheel on the shaft already on the machine, so the roller centres on the shaft itself rather than on a sleeve.
• 24 mm face width — spreads contact pressure along the full band height instead of a thin line that can squeeze glue out of the joint.
• White rubber compound — specified for the heated area behind the glue pot and specified as wear-resistant; the white face also shows a polished, hardened ring early.
• Rubber, not hard plastic — a compliant face follows the band on wood, plastic and laminate edges rather than skidding across it.
• Matched to the CEHISA roller position — drops into the 62 × 16 × 24 mm station on CEHISA CNC edge banding machines without re-machining the shaft or the bracket.
• Other sizes from the same range — 48–70 mm outside diameter, 8–18 mm bore and 12–27 mm width cover the other pressure stations in one order.

The usual choice is an OEM wheel with an OEM wait, or an unbranded wheel nobody has measured. PSW021 is bought by number, so neither is necessary.

• The part number carries the specification. Order PSW021 and the 62 × 16 × 24 mm figures come with it, so the wheel in next quarter's box matches the one on the machine now.
• A bore that fits, not nearly fits. A wheel that sits off centre loads one side of the band; a 16 mm bore running on the correct shaft keeps pressure symmetrical across the full 24 mm face.
• Wear you can see before you feel it. A white face turns a hardened, glazed surface into a polished ring, so the wheel goes on a planned stop instead of after a run of weak edges.
• One station, not the whole machine. The roller is a single part held on its own shaft, so a change does not disturb the glue pot, the trimming units or the 24 mm band height it was set for.
• Buy by number, not by photo. Spare rollers are consumables; ordering the same PSW021 code each time keeps every station on the machine supplied from one measured size.

Yes, when the wheel already on your machine measures 62 mm outside diameter, 16 mm bore and 24 mm thickness. PSW021 is listed for CEHISA CNC edge banding machines and for any unit using that same roller position — the three figures, not the badge on the frame, decide the fit.

φ62 × φ16 × 24 mm — 62 mm outside diameter, 16 mm inside diameter, 24 mm thick. The wheel is moulded in white rubber and catalogued as PSW021.

Yes, the three names describe the same part. Catalogues list it as press roller, pressure roller, press wheel or rubber pressure wheel; on an edge bander it is the wheel that presses the band onto the freshly glued panel edge.

Wood, plastic and laminate banding. A rubber face follows the band instead of skidding over it, which is why one 62 × 16 × 24 mm wheel covers all three material families on the same machine.

Yes. Alternate sizes run from 48 mm to 70 mm outside diameter, with 8–18 mm bores and 12–27 mm widths, so the other pressure stations can come in the same shipment as this one.

White is the finish specified for this roller, and it makes wear visible. A hardened, glazed face shows as a polished ring on white rubber, so the wheel is changed at a planned stop; the black parts on the same machine are usually bracket rollers doing a different job.

Measure the old wheel across the outside, across the bore and across the face. If those three numbers read 62 mm, 16 mm and 24 mm, PSW021 is the one; if they differ, the listed range still covers 48–70 mm outside diameter.

Check three numbers and one colour: 62 mm outside diameter, 16 mm bore, 24 mm width, white rubber. Then slide it onto the shaft by hand before the machine is restarted — it should seat without force and without play.