62x8x25mm Press Roller Rubber Wheel For Woodworking Edge Banding Machine

Need to put a CNC edgebander back on the line without waiting for an import order? The PSW018 press roller rubber wheel is 62 mm outside diameter, 8 mm bore and 25 mm thick, so it goes onto the existing shaft and presses the same 25 mm band as the worn part. One solid rubber body, no bearing, grey finish, part number PSW018. It runs on wood, plastic and laminate banding and fits the 62 × 8 × 25 mm pressure position on Homag, Biesse, SCM and Cehisa machines. Ten other sizes are in the same series.

A shop running a CNC edgebander meets the same three problems every time a pressure wheel wears out: the band stops sitting flat on the panel and the joint opens along one side, the outside diameter has gone oval so pressure differs from panel to panel, and the replacement has to be chased from a photo while the machine stands idle.

The PSW018 press roller rubber wheel is built for that position. It is a solid rubber wheel of 62 mm outside diameter, 8 mm bore and 25 mm thickness, sized for the pressure unit of a CNC edgebander, and it lays a 25 mm contact band on the edge without running onto the panel face.

The wheel is moulded as one rubber body with a plain 8 mm bore. There is no bearing and no separate hub, so the 62 mm outside diameter is the only working surface and the shaft keeps the fit it was machined for. Finish is grey; the part number is PSW018.

It presses wood, plastic and laminate edge banding, and the same 62 × 8 × 25 mm size serves the pressure stations of Homag, Biesse, SCM and Cehisa edgebanders. Customization is supported, and ten further diameter and width combinations are kept in this series.

What separates this wheel from a generic rubber roller:

• Three fixed dimensions — 62 mm outside diameter, 8 mm inside diameter, 25 mm thickness, so the wheel is ordered by size.
• A 25 mm contact band — the thickness matches the roll width, so the band is pressed in one pass.
• One-piece rubber body — moulded as a single rubber wheel, with no bearing, no insert and no separate hub.
• Plain 8 mm bore — the wheel turns on the existing shaft, so nothing else on the pressure unit has to be replaced.
• Wear stays on the rubber — the 62 mm face is the contact surface, so the wheel is swapped, not the unit.
• Three banding materials — wood, plastic and laminate edges run against the same grey rubber face.
• Fits four machine makes — Homag, Biesse, SCM and Cehisa pressure units that take a 62 × 8 × 25 mm wheel.
• Ten sizes in the series — 48 mm to 70 mm outside diameter, 8 mm to 18 mm bores and 12 mm to 27 mm widths.
• Part number PSW018 — one number covers the 62 × 8 × 25 mm wheel, so a reorder does not depend on a photo.
• Customization supported — bore and width can be made to a drawing when the 62 × 8 × 25 mm size does not fit.

A worn wheel leaves two bad options: run on with open joints, or stop the machine until a part arrives. This one closes both.

• Replace the wheel, not the unit. The 8 mm bore slides onto the shaft already on the machine, so one 62 mm rubber wheel brings the pressure station back without touching the cylinder.
• One number for every reorder. PSW018 is the 62 × 8 × 25 mm wheel, so the tenth order is the same line item as the first, with no new photo and no new guess.
• Even pressure across the edge. A full 25 mm contact band holds the band over its whole width, not on a strip that lets the top edge lift.
• Four machine makes, one bin. Homag, Biesse, SCM and Cehisa units taking 62 × 8 × 25 mm are one part, so a mixed shop keeps one stock line.
• Ten sizes behind one number. When the next machine needs 48 mm, 65 mm or 70 mm, the same series covers it.
• Made to a drawing when stock will not fit. Customization is supported, so a non-standard bore or width is quoted against your drawing, not improvised on the floor.
• A consumable, not a capital part. At 62 mm outside diameter this is a rubber wear item, bought in the quantity the line consumes and kept in a drawer.

62 mm outside diameter, 8 mm inside diameter and 25 mm thick. Those three numbers are the whole specification of the part, and the bore is a plain 8 mm hole with no bearing inside.

It fits any pressure station that takes a 62 × 8 × 25 mm wheel. The same size is used on Homag, Biesse, SCM and Cehisa edgebanders, so measure the old wheel across the outside, the bore and the width before ordering.

No. The wheel is one moulded rubber body with a plain 8 mm bore. It turns on the machine shaft, which is why the outside diameter is the only part that wears.

Wood, plastic and laminate. All three run against the same grey rubber face, and the 25 mm width covers a full band width in one pass.

One wheel. PSW018 is supplied as a single 62 × 8 × 25 mm rubber wheel, so you order the number the line consumes rather than a fixed set.

Yes. The same series covers ten other combinations from 48 mm to 70 mm outside diameter, including 65×8×25, 60×8×23 and 70×18×25 mm, and customization is supported.

When the 62 mm outside diameter no longer reads 62 mm, or when the band starts lifting along one side of the edge. Both point to a wheel that has worn or gone oval, not to a fault in the pressure cylinder.

Quote the part number PSW018 together with the size 62 × 8 × 25 mm, and add the machine make and model. Send a photo of the old wheel next to a rule if the three dimensions on your machine are not certain.