KDT Edgebander Glue Pot Gate Glue Pot Accessoreis For KDT Edgebanding Machine

Product Description

Replacing a worn glue pot gate on a KDT edgebander should not mean buying a new pot. This gate is a steel part of 0.25 kg, 190 mm long, 28 mm wide, with a 16 mm D1 and 10 mm D2, listed as a glue pot spare for KDT edgebanding machines in both forward and reverse versions. It goes into the existing pot, so the housing and the heating side stay on the machine. Price is on request: quote the direction you need and send a photo of the old gate.

A glue line that runs short, then floods, then runs short again is rarely a glue problem. It is the gate at the pot outlet: worn at the seat, fretted on the stem, or held open by cured adhesive. The shop is left with three bad options - buy a complete glue pot, wait for a service visit with the line down, or keep running and rework every banded edge. Each costs more than the one part that failed.

This is that part, sold on its own: the glue pot gate for KDT edgebanding machines. It is a steel gate, 190 mm long and 28 mm wide, 0.25 kg with 16 mm D1 and 10 mm D2. It is listed under glue pot spares for KDT edgebanders, and it fits the existing pot rather than replacing it.

Forward and reverse are both listed, as 2 versions of the same part. Which one you need is decided by the way the old gate sits in the pot, so check the direction first - a photo of the part shows it in one shot.

At 0.25 kg a gate travels as a small parcel, so a second one is worth keeping on the shelf: when the running gate hesitates, the line is down only for the time it takes to swap a part. Brand is SHUNHONGYU, or unmarked.

Product Features

What this glue pot gate is, and the details that decide a match.

• Part role - the gate that regulates glue release at the pot outlet of a KDT edgebander, supplied on its own, not as a complete pot.
• Length - 190 mm end to end, the first dimension to measure on the old gate.
• Section - 28 mm wide, with 16 mm D1 and 10 mm D2 across the two seats.
• Weight - 0.25 kg per piece, small enough to hold a second one as a shelf spare.
• Material - steel body, a machined part that is replaced as a unit rather than repaired on the bench.
• Direction - listed in forward and reverse, 2 orientations, so the way it sits in the pot is checked before the order.
• Machine family - for KDT edgebanding machines; this is a KDT pot spare, not a universal gate.
• Application slot - glue pot spares for KDT edgebanders, in the glue circuit rather than the trimming or pressure station.
• Brand - SHUNHONGYU, or supplied blank where an unmarked part is asked for.
• Price - on request; the listing fixes no number, so 1 gate and a gate with other pot spares are quoted apart.

Product Parameters

Product Advantages

The choice on a gate that no longer closes cleanly is narrow: buy the whole pot back, or change the one steel part that wore out.

• Replace the gate, not the pot. A gate is 1 component of the pot assembly. Buying the pot back means paying again for the housing, the heating side and the seals that were still working.
• Two orientations, one thing to check. Forward and reverse are both listed, so the question that decides the fit is answered by the old part in your hand, not by a guess on the phone.
• Sized to sit on a shelf. 0.25 kg and 190 mm mean a spare gate costs almost nothing to hold, and a hesitation at the pot is a 1-part swap instead of a 2-week wait.
• Numbers you can measure yourself. 28 mm width, 16 mm D1 and 10 mm D2: a caliper on the old gate confirms the match before any money moves.
• One order for the wear set. Other glue pot spares are quoted on the same line, so the pot goes back together in 1 shipment instead of 2 or 3.
• Steel, replaced as a unit. The gate is a steel part with no liner to peel out and no adhesive face to clean back, so it is changed rather than serviced.

Frequently Asked Questions

Will this glue pot gate fit my KDT edgebander?

Yes, if your machine is a KDT edgebander and the old gate carries these dimensions. It is listed as a glue pot spare for KDT edgebanders, so the check is the machine family plus 190 mm length, 28 mm width and the 16 mm D1 / 10 mm D2 seats.

Forward or reverse - which version do I need?

Match the direction of the gate you are taking out. Both forward and reverse are listed as 2 versions, and the old part shows which way it sits in the pot; a photo of the gate in place settles it.

How do I confirm the size before I pay?

Measure the old gate: 190 mm long, 28 mm wide, 16 mm D1 and 10 mm D2, 0.25 kg. A photo of the part next to a rule is faster than any written description, and it costs nothing to send.

Do I have to buy the whole glue pot as well?

No. The gate is sold on its own as a glue pot spare. The pot, the heating side and the mounting stay on the machine, which is the point of replacing a 0.25 kg part instead of the pot.

What is the gate made of?

Steel. The listing gives a steel body, so the gate is a machined part that is replaced as a unit rather than repaired on the bench.

How heavy is one gate, and how does it travel?

0.25 kg per piece. At that weight 1 gate ships as a small parcel rather than on a pallet, so a spare can be ordered with other pot spares and packed together.

What does the gate cost?

Price is on request. Nothing is fixed on the listing, because 1 gate alone and a gate with other glue pot spares are quoted apart; send the quantity and a quote follows.

What should I put in the enquiry?

The machine model, the direction (forward or reverse) and a photo of the old gate. Those 3 things answer both the fit question and the price question in one reply.