Nanxing Edge Bander Spare Conveyor Belt Feeding Device Edgebanding Machinery

Panel slipping on a KDT or NANXING edge bander? This is the spare conveyor belt feeding device, part number 48336387: a steel assembly with two ball bearings in one block, two meshing toothed wheels and a knurled feed knob with a hex socket. Condition is new, and it is also listed as the KDT edgebander belt feeding device. Send the machine brand and a photo of the old unit, and the price is quoted per order — shipment by DHL, FedEx or UPS.

A conveyor that lets the panel slip on an edge bander shows up in three places: the panel skews on its way into the gluing station, the band comes out proud on one edge and thin on the other, and the line stops while somebody decides whether the fault is the belt, a bearing or the drive. All three lead back to one part, the feeding device that carries each panel past the stations.

This is that part, the conveyor belt feeding device supplied as a spare for KDT and NANXING edge banders. It is a steel assembly: one solid block holding two ball bearings on the outer shaft, two meshing toothed wheels inside the block, and a knurled feed knob on the shaft end.

The knob is the setting, and its centre carries a hex socket, so belt position is adjusted with an Allen key instead of by pressing on the belt by hand. The block mounts on one flat face and has a single lug with a through hole, so it drops onto the frame in one position.

Material is steel, condition new, part number 48336387. Shipment runs by DHL, FedEx or UPS, or by air and by sea on larger orders.

What the assembly is, in the terms that decide whether it fits the station:

• Steel block — the bearing housing is steel, machined on one face and drilled for a single mounting lug.
• Two bearings on the shaft — two ball bearings sit in the block around the outer shaft, so the knob turns on rolling contact rather than in a bore.
• Two toothed wheels — the meshing pair ties the knob to the belt shaft at a fixed ratio, so one turn of the knob moves the belt by one amount.
• Knurled knob, hex socket — the outer end is knurled for grip and ends in an internal hex, so tension is set with an Allen key.
• One lug, one position — a single mounting ear with a through hole locates the block against the frame, so it refits the way it came off.
• KDT and NANXING — listed as spares for KDT / NANXING edgebanders, the two makes named in this part's data.
• New, not rebuilt — condition is new on the record, so the bearings and wheels arrive as an assembly.
• Order by part number — 48336387 covers the whole assembly: the reference for the enquiry and the purchase order.
• Three ways out — shipment by DHL, FedEx or UPS express, by air, or by sea.

A belt that drifts leaves two habits: standing at the infeed to straighten panels, or booking the feed unit off the line. A spare on the shelf ends both.

• The setting repeats. The knurled knob and its hex socket put belt position back on a key, so the next operator reaches the same setting.
• Two bearings take the load. The shaft turns in two ball bearings in a steel block, not in a plain bore.
• The panel stops skewing. A device that holds its setting carries each panel past the stations at one speed, which is what keeps the band even.
• One part, not a rebuild. The assembly comes off as one unit on a single lug, so the change is a swap, not a strip-down.
• Right for the machine you run. Spares for KDT / NANXING edgebanders: name the make and the quantity, and it is quoted against that.
• New condition. Recorded as new, so the bearings and toothed wheels are not carrying somebody else's hours.
• Three carriers to choose from. DHL, FedEx or UPS for a single assembly, air and sea for larger orders.
• A quoted price, not a guess. Send 48336387, the machine brand and the quantity, and the price comes back against that order.

Yes, if the worn part is the conveyor belt feeding device on a NANXING edge bander. The listing is for spares for KDT and NANXING edgebanders, part number 48336387, and the photos on this page show the assembly you should compare against the old unit.

Yes. The application line covers spares for both KDT and NANXING edgebanders, so the same assembly is ordered for either make. Send the machine brand with the order so the part is quoted against the right station.

One feeding assembly: the steel bearing block with two ball bearings, the pair of meshing toothed wheels, the knurled feed knob with its hex socket, and the single mounting lug. The quantity is whatever you order, and the price is quoted per order.

No. Send the machine brand, the part number 48336387 and a photo of the old unit; the part is matched on that, not on a drawing. Photos of the old assembly from two angles are enough to confirm it is the same feeding device.

New. The condition on the record is new, so the bearings and toothed wheels arrive as a complete assembly rather than a worn unit to be assessed on the bench.

Steel. Material on this part is steel, and the bearing block is the machined body that carries the two bearings, the two toothed wheels and the mounting lug.

By express with DHL, FedEx or UPS, or by air and by sea on larger orders. The carrier is picked on the order so a single assembly moves without waiting on a container.

Send the part number, the machine brand and the quantity, and the price is quoted per order. There is no list price on this page because the assembly is quoted against the order.