4014020623 DIAMOND RADIUS CUTTERS I-SYSTEM HSK25R - PCD Trimming Cutter

Need to trim edge banding and form a 2 mm corner radius on a Homag edge bander without guessing the size? The 4014020623 PCD trimming cutter is the answer in one line: 76 mm cutting diameter, HSK25R shank, 23 mm height, R2 radius, 4T diamond teeth. Part number 4014020623, size code 76xHSK25RxH23xR2x4T — diameter, interface, height, radius and tooth count all sit in that one string, so a replacement is a copy-paste rather than a description.

A shop running an edge bander runs into the same three things: the corner radius starts chipping long before the panel does, a replacement cutter arrives with the right part number but the wrong size code, and rough trimming and radius trimming get ordered as if they were the same tool. The 4014020623 PCD trimming cutter is built around the third of those, and it makes the first two easier to avoid.

It is a PCD (polycrystalline diamond) radius trimming cutter with a 76 mm cutting diameter, an HSK25R shank, a 23 mm height, an R2 radius and 4T — four diamond teeth. The complete size code is 76xHSK25RxH23xR2x4T, so diameter, interface, height, radius and tooth count travel together in a single string.

The 2 mm radius is a form in the tooth profile, not a setting on the machine, which is why an R2 tool and an R3 tool are two different cutters rather than two adjustments. The tool is listed for Homag machines as a cutting tool, and the cutting edge is diamond rather than carbide.

Named work for this cutter is hardwood, plywood, MDF, engineered wood panels and composite materials, plus trimming and finishing in furniture production. Order by part number 4014020623 and check the size code 76xHSK25RxH23xR2x4T before the tool goes anywhere near the spindle.

What makes this a radius trimming cutter rather than a generic disc is below — every line carries a figure you can check against your own station.

• PCD cutting edge — polycrystalline diamond is the tip material on all 4 teeth, not carbide.
• HSK25R shank — the interface is cut into the tool body, so it seats on an HSK25R spindle without an adapter in between.
• 76 mm cutting diameter — the 76 mm circle in the size code is measured across the cutting edge, matching a 76 mm trimming station.
• R2 radius form — a 2 mm corner radius is ground into the tooth profile; an R3 corner needs a tool whose code reads R3.
• Four teeth — 4T around a 76 mm body, so each diamond tip takes a quarter of the circumference.
• 23 mm height — the H23 in the code is the body height, quoted in the same string as diameter and radius.
• I-System series — the cutter is listed under the I-System together with part number 4014020623.
• Homag application — the tool record states cutting tool for Homag machines, so the reference is machine-family specific, not universal.
• One-string identification — 4014020623 plus 76xHSK25RxH23xR2x4T identifies the tool without a photo or a drawing.
• Material range — hardwood, plywood, MDF, engineered wood and composite panels are all named for this cutter.

Chosen from a photo, a radius cutter fails in two ways: it arrives with the wrong radius, or it will not seat on the shank. On a running shift neither is recoverable, so the figures below are the ones worth checking first.

• Ordered by number, not by picture. 4014020623 names the tool and 76xHSK25RxH23xR2x4T names the geometry, so a reorder is a copy-paste instead of a description.
• The radius is fixed in the tool. R2 is a 2 mm form in the tooth, so every cutter of this code produces the same corner; a 3 mm corner means a different code.
• Nothing between spindle and tool. the HSK25R taper sits on the cutter itself, which removes one joint from the stack.
• Diamond where the work happens. 4 PCD tips carry the trimming edge, so the hardest part of the tool is the part that touches the band.
• Trim and corner at one station. a 76 mm cutter takes the protruding band and the R2 form shapes the corner with the same tool.
• A replacement that still matches. 23 mm height and 4T are baked into the code, so next year's order fits the same station as this year's.
• The panels you actually run. hardwood, plywood, MDF and composite panels are the named materials, which covers furniture trimming and composite work.

Only if your trimming station takes an HSK25R shank and an R2 profile. The tool is listed as a cutting tool for Homag machines, but the two figures that decide fit are the interface and the radius — read both off the old tool before ordering.

It is the whole tool in one string: 76 mm diameter, HSK25R shank, 23 mm height, R2 radius, 4 teeth. Quote the full code and nothing about the geometry is left to interpret.

It is a radius trimming cutter. Both the product name and the size code carry an R2 radius form, so the tool shapes the corner rather than hogging off the bulk of the band in a first pass.

PCD, polycrystalline diamond. Diamond is the tip material on the 4 teeth; the body of the cutter is not the cutting edge.

Because 4T on a 76 mm body fixes how the load is spread. Four tips around a 76 mm circle put a quarter of the circumference on each tooth, and that geometry is locked into the size code.

Hardwood, plywood, MDF, engineered wood and composite panels. Those are the materials named for this cutter in the tool record.

Not from this code. The radius lives in the size string, so a 3 mm corner needs a tool coded R3 — 76xHSK25RxH23xR2x4T is the R2 version.

Quote part number 4014020623 together with the size code 76xHSK25RxH23xR2x4T; price is on request. Sending both strings lets the supplier confirm the geometry before the tool ships.